-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
- When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
- Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
- When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
- When I attempted to download a project to a CPU with user ROM card by using D300win, a message appeared saying 'Invalid loader command process!' an...
GLOBAL
Search by category
Keyword Search
FAQ within [ SPH ]
-
The near zero signal/command pulse zero signal/positioning end signal/RDY signal of the status information signals are set to [1]. The interrupt input sig... Show Detail
- No：1318
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:17
- Category： Function
-
The amounts of data transmitted or received are not limited as R_WRITE instruction/R_READ instruction but by the capacity of the memory from/to which data ar... Show Detail
- No：1324
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
-
An order for one NP8B-BP means one plug will be delivered. If you need two plugs, order two pieces. The CPU module (Type_ NP1P***) and integrated type int... Show Detail
- No：1338
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:34
- Category： Accessory
-
The P-link memory is prepared in the P-link module. It is separate from the memory in the CPU and no change takes place at the time of switchover to a standb... Show Detail
- No：1343
- Displayed Date：2023/04/25 19:00
- Category： Main unit
-
I cannot register a dummy module (Type_ NP1F-DMY) with the system definitions using the loader.
The purpose of a dummy module is to use it as a temporary replacement of an I/O module that has been defined with the system but does not actually exist for ... Show Detail
- No：1348
- Displayed Date：2023/04/25 19:00
- Category： Function
-
What is the dummy module (Type_ NP1F-DMY) used for? Is it required for an unused slot?
In an SX system, removing any I/O module that has failed causes the CPU to stop running due to a 'system definition mismatch.' In a case like this, a dummy ... Show Detail
- No：1349
- Displayed Date：2023/04/25 19:00
- Category： Function
-
The base board that plays the role of a hub of optical converter modules is not represented in the system definitions. When the power supply (PS) of the sam... Show Detail
- No：1351
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
It is possible with the Ethernet module software version V36 or later by using the F_READ (read)/F_WRITE (write) FB. After writing, the power (or reset) o... Show Detail
- No：1370
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:42
- Category： Communication (Ethernet)
-
Only open-collector (single-ended) signals are accepted. (NP1F-HC2 accepts differential signals.) The rated current is 40 mA and an encoder that permits t... Show Detail
- No：1373
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:43
- Category： Function
-
Is there an RAS that detects an error of the external power supply used for an I/O module?
No, there isn't. Receive the external power supply as an external input to detect the status. Show Detail
- No：1388
- Displayed Date：2023/04/25 19:00
- Category： Main unit
31-40 of Total 235