Check the following two points (1) To use the EMG/±OT signal, input the 'External power supply 24 V DC.' (2) Check the

Proportional band P is the % of the variation range of input PV required for the change of output MV in the effective va

It counts the number of transmissions of message processing M_RECEIVE and M_SEND performed on the SX bus.

The influence of external resistance on the thermocouple input is approximately 0.3 ?V/?. The measurement accuracy of t

The following analog input modules have the moving average function. 1) For the following models, the moving average f

The existing MICREX-F program does not need any modification.

The multiplication of the high-speed counter module is automatically set as follows depending on the input pulse form_

Set the port No. as described below. (1) For NP1L-RS2_ Set '0.' (2) For NP1L-RS4_ Set '1.' See the figure below for th

For an analog input range (1 to 5 V or 4 to 20 mA), a line breakage detection function is provided. An input voltage of

Use the 'Excitation timing output' signal for the Z-phase pulse when a stepping motor is used.

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC > SPH

Latest FAQ

When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
When I attempted to download a project to a CPU with user ROM card by using D300win, a message appeared saying 'Invalid loader command process!' an...

GLOBAL

Search by category

Keyword Search

FAQ within [ SPH ]

221-230 of Total 235

≪ 23 / 24page ≫

When I turned on the positioning control module (Type_ NP1F-MP2/MA2), the EMG/±OT LED lights up and positioning operation is disabled. What causes ...

Check the following two points (1) To use the EMG/±OT signal, input the 'External power supply 24 V DC.' (2) Check the wiring of the external equipment. (T... Show Detail
- No：1601
- Displayed Date：2023/04/25 19:00
- Category： Function
In PPID, a POU for the PID FB package, which range does the % of proportional band P account for?

Proportional band P is the % of the variation range of input PV required for the change of output MV in the effective variation range from 0 to 100%. It is... Show Detail
- No：1580
- Displayed Date：2023/04/25 19:00
- Category： Function
What does the sending/receiving counter for the structure variable RAS.RAS of the non-procedure standard expansion FB for communication _Cfr* count...

It counts the number of transmissions of message processing M_RECEIVE and M_SEND performed on the SX bus. Show Detail
- No：1569
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
Is the measurement accuracy affected when an external arrestor for protection is mounted on the input terminal of the thermocouple input module (Ty...

The influence of external resistance on the thermocouple input is approximately 0.3 ?V/?. The measurement accuracy of the thermocouple input is affected by... Show Detail
- No：1545
- Displayed Date：2023/04/25 19:00
- Category： I/O
Is there an analog module that supports the moving average function?

The following analog input modules have the moving average function. 1) For the following models, the moving average function can be set by switch setting ... Show Detail
- No：1493
- Displayed Date：2023/04/25 19:00
- Category： I/O
An existing P-link system is composed of MICREX-F. If part of it is replaced with P-link of MICREX-SX, does the existing MICREX-F program need to b...

The existing MICREX-F program does not need any modification. Show Detail
- No：1319
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
I use the high-speed counter module (Type_ NP1F-HC□). The user's manual (FEH210) shows 'Multiplication function_ x1, x4.' How can I switch between ...

The multiplication of the high-speed counter module is automatically set as follows depending on the input pulse form_ ･ Forward pulse + Reverse pulse_ x1 ... Show Detail
- No：1564
- Displayed Date：2023/04/25 19:00
- Category： Function
For the initial setting of a general-purpose communication module with only one communication port such as NP1L-RS2 and NP1L-RS4, is it correct to ...

Set the port No. as described below. (1) For NP1L-RS2_ Set '0.' (2) For NP1L-RS4_ Set '1.' See the figure below for the setting for each type of genera... Show Detail
- No：1383
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:45
- Category： Communication (Others)
I understand that an analog input module (Type_ NP1AXH4-MR, etc.) has a signal line breakage detection function. How does it work?

For an analog input range (1 to 5 V or 4 to 20 mA), a line breakage detection function is provided. An input voltage of 0.92 V or lower for the 1 to 5 V ran... Show Detail
- No：1316
- Displayed Date：2023/04/25 19:00
- Category： I/O
How can I provide Z-phase pulses when the equipment connected with the positioning control module (Type_ NP1F-MP2/MA2) uses a stepping motor?

Use the 'Excitation timing output' signal for the Z-phase pulse when a stepping motor is used. Show Detail
- No：1574
- Displayed Date：2023/04/25 19:00
- Category： Function

221-230 of Total 235

SPH

I/O
Error

Support tool

Info & News

To Top of Page

PKSHA FAQ logo

SPH

Regional Websites

About Us

Products & Solutions

Investor Relations

Sustainability