-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
- When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
- Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
- When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
- When I attempted to download a project to a CPU with user ROM card by using D300win, a message appeared saying 'Invalid loader command process!' an...
GLOBAL
Search by category
Keyword Search
FAQ within [ SPH ]
-
Yes, a CPU is necessary. In the case of a system with no CPU, the input status LED does not work even if signals are externally input into the input module. Show Detail
- No：1537
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
The SX bus connector of the SPH300EX (Type_ NP1PS-74D) is an OUT (output) connector. When you connect SX bus equipment, connect the cable to the IN (input)... Show Detail
- No：1535
- Displayed Date：2023/04/25 19:00
- Category： Main unit
-
No, you cannot. Use the dedicated loader cable (Type_NW0H-CA3). Show Detail
- No：1511
- Displayed Date：2023/04/25 19:00
- Category： Support tool
-
I use Expert (D300win). Can I check the download history to the CPU?
When downloading a project (including Patch POU), you can save the download history in your personal computer or the CPU module. [Setting procedure] ・In t... Show Detail
- No：1490
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
-
The memory usage is displayed in 'GM (global memory)' by the 'Device' function that is used to edit tags or check the memory usage. However, the memory cap... Show Detail
- No：1484
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
-
How can I change the CPU type in an already created project?
Refer to 'Appendix 3-2 Procedure for Changing Resource (CPU type)' in the User's Manual 'Instructions' (FEH200 with index 'o' or later). Show Detail
- No：1467
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
-
Doesn't the connector type I/O module of the SPH Series include a connector as an accessory?
The SPH Series does not include an I/O connector. A soldering type connector is available as an option sold separately (NP8V-CN). Show Detail
- No：1426
- Displayed Date：2023/04/25 19:00
- Category： I/O
-
With a general-purpose communication module, is RS232C completely full duplex?
It is full duplex for both hardware and software (firmware) for anything other than communication by M_RECEIVE and M_SEND on the SX bus, which are FB interna... Show Detail
- No：1413
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
It takes place only when data are received from an external device. Show Detail
- No：1400
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
The module is equipped with 2 channels of high-speed counter and signals of a different voltage can be counted for each channel. To set the signal level, s... Show Detail
- No：1398
- Displayed Date：2023/04/25 19:00
- Category： Function
201-210 of Total 235