The following are necessary. 1) Hardware Ethernet interface module (NP1L-ET1) or CPU module with built-in Ethern

In a redundant system, both CPUs are identified as CPU0 and you cannot read a battery error of the standby CPU. Determin

The minimum required products are (1) High-performance CPU exclusively for the electronic cam, (2) pulse train combine

There is a possibility of mismatch between the project in the user ROM card and the CPU memory. On the 'Failure diagnosi

You can use it provided that the system is a single-unit system (configured with one base only). Connect the connectors

No, it does not support multicast transmission (sending/receiving). It does support broadcast transmission (sending/rec

It might be counting noise as a pulse. Take the following measures_ (1) Isolate the pulse generator and PLC from the noi

With FL-net, Class C IP addresses are used. The range of Class C IP addresses is 192.0.0.* to 233.255.255.*. (Range of

No, you cannot upload a definition file. So, it is very important to keep backup of Definition file on PC side.

The SX-Programmer Expert supports MODBUS communication (master function) using an FB. Communication with a MODBUS slave

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC > SPH

Latest FAQ

When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
When I attempted to download a project to a CPU with user ROM card by using D300win, a message appeared saying 'Invalid loader command process!' an...

GLOBAL

Search by category

Keyword Search

FAQ within [ SPH ]

11-20 of Total 235

≪ 2 / 24page ≫

What is necessary for MODBUS_TCP communication between SPH and an external device?

The following are necessary. 1) Hardware Ethernet interface module (NP1L-ET1) or CPU module with built-in Ethernet (SPH2000/3000 series CPU types w... Show Detail
- No：1470
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:30
- Category： Communication (Ethernet)
An address error occurs when I read a battery error of the standby CPU (CPU1) from the operating CPU (CPU0).

In a redundant system, both CPUs are identified as CPU0 and you cannot read a battery error of the standby CPU. Determine the condition of the standby CPU fr... Show Detail
- No：1572
- Displayed Date：2023/04/25 19:00
- Category： Application
Which devices are required for controlling an electronic cam with the SPH Series? What should I prepare?

The minimum required products are (1) High-performance CPU exclusively for the electronic cam, (2) pulse train combined module (Type_ NP1F-MP2) or anal... Show Detail
- No：1323
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:20
- Category： Function
When I attempted to download a project to a CPU with user ROM card by using D300win, a message appeared saying 'Invalid loader command process!' an...

There is a possibility of mismatch between the project in the user ROM card and the CPU memory. On the 'Failure diagnosis' dialog, check the 'Resource inform... Show Detail
- No：1671
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
I don't have the SX bus loop-back plug (Type_ NP8B-BP). Can I use the SX bus cable instead?

You can use it provided that the system is a single-unit system (configured with one base only). Connect the connectors at both ends of the cable to IN and ... Show Detail
- No：1543
- Displayed Date：2023/04/25 19:00
- Category： Accessory
Does the Ethernet module of the MICREX-SX (Type_ NP1L-ET1/ET2) support TCP/IP multicast transmission (sending/receiving)?

No, it does not support multicast transmission (sending/receiving). It does support broadcast transmission (sending/receiving). Show Detail
- No：1536
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
I use the SPH and the high-speed counter module seems to count more than actual values. What is a possible cause?

It might be counting noise as a pulse. Take the following measures_ (1) Isolate the pulse generator and PLC from the noise source and shorten the wiring dist... Show Detail
- No：1427
- Displayed Date：2023/04/25 19:00
- Category： Function
What is the range of IP addresses that can be used for FL-net?

With FL-net, Class C IP addresses are used. The range of Class C IP addresses is 192.0.0.* to 233.255.255.*. (Range of *_ 1 to 254) Show Detail
- No：1301
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 14:19
- Category： Communication (Others)
Can I upload a definition file downloaded from a configurator to NP1L-PD1/PD2?

No, you cannot upload a definition file. So, it is very important to keep backup of Definition file on PC side. Show Detail
- No：1468
- Displayed Date：2023/04/25 19:00
- Category： Support tool
Does an RS-485 communication module (Type_ NP1L-RS1/RS4/RS5, etc.) support the MODBUS procedure?

The SX-Programmer Expert supports MODBUS communication (master function) using an FB. Communication with a MODBUS slave device is possible by using SPH_CP... Show Detail
- No：1380
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:45
- Category： Communication (Others)