During battery-less operation, previous fault information and other 'history of RAS' are not saved. Only the present RAS

To use a CF card as user ROM of the SPH Series, you need to format the CF card and initialize it (generate folders and f

You can order sulfurized gas-resistant models by adding /Z4 at the end of product type code of the MICREX-SX SPH. Or, co

It is possible as long as the protocol is UDP/IP. In the M_OPEN FB, specify 255.255.255.255 as the IP address to be set

Note the following points (1) The rated output voltage is 12 to 24 V. Check the voltage of the device to be connected.

It may be caused by noise. Check the surrounding environment and wiring routes for any problem. The lowered communicati

(1) Standard CPU_ Access takes place when tasks end (synchronized with tasks). (2) High-performance CPU_ Access takes p

No, it is not possible. Only one program can be stored.

To enable the 'output value reference input,' the output module must be actually mounted. If the output module is set as

In the MV selection part in the PID FB, (1) the backward operation uses the internally calculated MV value (%) without p

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC > SPH

Latest FAQ

When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
When I attempted to download a project to a CPU with user ROM card by using D300win, a message appeared saying 'Invalid loader command process!' an...

GLOBAL

Search by category

Keyword Search

FAQ within [ SPH ]

181-190 of Total 235

≪ 19 / 24page ≫

When you use battery-less operation on the SPH, is the history of RAS information recorded?

During battery-less operation, previous fault information and other 'history of RAS' are not saved. Only the present RAS information is displayed. Show Detail
- No：1579
- Displayed Date：2023/04/25 19:00
- Category： Main unit
What operation do I need to use a CF card as a user ROM card used for the CPU module of the SPH Series (SPH300 or SPH2000)?

To use a CF card as user ROM of the SPH Series, you need to format the CF card and initialize it (generate folders and files in the user ROM). The format sh... Show Detail
- No：1439
- Displayed Date：2023/04/25 19:00
- Category： Accessory
I want MICREX-SX SPH models designed to resist sulfurized gas.

You can order sulfurized gas-resistant models by adding /Z4 at the end of product type code of the MICREX-SX SPH. Or, contact your Fuji Electric sales repres... Show Detail
- No：1425
- Displayed Date：2023/04/25 19:00
- Category： Others
Is broadcast communication via Ethernet possible?

It is possible as long as the protocol is UDP/IP. In the M_OPEN FB, specify 255.255.255.255 as the IP address to be set for the 'communication destination s... Show Detail
- No：1415
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
I want to run an external device by pulse output with the high-speed output module (Type_ NP1Y32T09P1-A). What are the points to note regarding the...

Note the following points (1) The rated output voltage is 12 to 24 V. Check the voltage of the device to be connected. (2) The Z-phase/timing input signal f... Show Detail
- No：1399
- Displayed Date：2023/04/25 19:00
- Category： Function
I find the TER_LED of the T-link master module (Type_ NP1L-TL1) sometimes illuminated. The communication speed is lowered when it occurs.

It may be caused by noise. Check the surrounding environment and wiring routes for any problem. The lowered communication speed is assumed to be because t... Show Detail
- No：1339
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:34
- Category： Communication (T-link)
I use an Ethernet module (Type_ NP1L-ET1/ET2) to read/write data from/to a PC in the loader command communication mode. At what time are data read ...

(1) Standard CPU_ Access takes place when tasks end (synchronized with tasks). (2) High-performance CPU_ Access takes place when a request is generated rega... Show Detail
- No：1300
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
Can I store multiple programs in the user ROM card (CF or SD) ?

No, it is not possible. Only one program can be stored. Show Detail
- No：1298
- Displayed Date：2023/04/25 19:00
- Category： Main unit
In a multi-CPU system, I set the 'Output reference input' of the I/O group registration but the variable (contact) specified for the output referen...

To enable the 'output value reference input,' the output module must be actually mounted. If the output module is set as 'unimplemented' in the system config... Show Detail
- No：1637
- Displayed Date：2023/04/25 19:00
- Category： Application
What is the difference between the PID forward and backward operations when the PID FB package is used?

In the MV selection part in the PID FB, (1) the backward operation uses the internally calculated MV value (%) without processing it (as-is)_ and (2) the for... Show Detail
- No：1625
- Displayed Date：2023/04/25 19:00
- Category： Function