Yes, they are. The maximum size is 32 words including the actual data, start code, end code, and BCC. (The same applies

The SX bus connector of the SPH300EX (Type_ NP1PS-74D) is an OUT (output) connector. When you connect SX bus equipment,

Yes, it is possible. Use a card with the following memory capacities_ SPH300_ 2 GB or less SPH2000_ 32 GB or less (PI

No, you can't. The relationship between i, which is the sensor output current, and i1 and i2, which are the CH input cu

No, you can't. You can check the IP address by connecting the PC loader to the CPU module and monitoring the RAS informa

Unfortunately, information in a device connected to the master module cannot be read even by building a user application

The general-purpose communication function of Ethernet allows simplified broadcast communication. By using a CPU with b

Do not install an I/O terminal (Type_NR1S*-*, NR1T*-*, NR1J*-*, and NR1D*-*) on the floor of the panel because it has no

This was probably caused by one of the following two factors_ (1) ±OT is set to 'Disabled' in the parameter setting of

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC > SPH

Latest FAQ

When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
When I attempted to download a project to a CPU with user ROM card by using D300win, a message appeared saying 'Invalid loader command process!' an...

GLOBAL

Search by category

Keyword Search

FAQ within [ SPH ]

181-190 of Total 235

≪ 19 / 24page ≫

When using Cfr32, are the start code, end code, and BCC included in the maximum data size?

Yes, they are. The maximum size is 32 words including the actual data, start code, end code, and BCC. (The same applies to _Cfr64, _Cfr128, _Cfr252, and _Cfr... Show Detail
- No：1495
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
The SPH300EX (Type_ NP1PS-74D) has an SX bus connector. Which ports should I use when connecting the SX bus cable to the SX bus expansion base, 'IN...

The SX bus connector of the SPH300EX (Type_ NP1PS-74D) is an OUT (output) connector. When you connect SX bus equipment, connect the cable to the IN (input)... Show Detail
- No：1535
- Displayed Date：2023/04/25 19:00
- Category： Main unit
Is it possible to use a commercial CF card for the CPU module supporting CF card mounting?

Yes, it is possible. Use a card with the following memory capacities_ 　SPH300_ 2 GB or less SPH2000_ 32 GB or less (PIO mode supporting model) Note that so... Show Detail
- No：1593
- Displayed Date：2023/04/25 19:00
- Category： Accessory
I will use the analog current input module. Can I input a single input signal to two CHs of the module simultaneously (in parallel) to use them?

No, you can't. The relationship between i, which is the sensor output current, and i1 and i2, which are the CH input currents of the PLC, is expressed as i ... Show Detail
- No：1603
- Displayed Date：2023/04/25 19:00
- Category： I/O
When I forget the IP address of the WEB module (Type_ NP1L-WE1), can I change the IP from an external network?

No, you can't. You can check the IP address by connecting the PC loader to the CPU module and monitoring the RAS information of the fault diagnosis function. Show Detail
- No：1616
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
With an Ethernet module (Type_ NP1L-ET1/ET2), is the protocol for fixed buffer communication the same as that of MICREX-F?

Yes, it is the same. Show Detail
- No：1377
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
Is there any way to check the vendor ID, product code, product revision, serial No., etc. of the slave from the DeviceNet master module (Type_ NP1L...

Unfortunately, information in a device connected to the master module cannot be read even by building a user application. Please use the dedicated configura... Show Detail
- No：1387
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
Can I perform broadcast communication between CPU modules without using FL-net or P/PE-link module?

The general-purpose communication function of Ethernet allows simplified broadcast communication. By using a CPU with built-in Ethernet, you can build a bro... Show Detail
- No：1485
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
Can I install an I/O terminal (Type_NR1S*-*, NR1T*-*, NR1J*-*, and NR1D*-*) in the vertical direction on the panel?

Do not install an I/O terminal (Type_NR1S*-*, NR1T*-*, NR1J*-*, and NR1D*-*) on the floor of the panel because it has no ventilation slit for cooling. You ca... Show Detail
- No：1520
- Displayed Date：2023/04/25 19:00
- Category： I/O
Although the LED for ±OT lights up on the positioning control module (Type_ NP1F-MP2/MA2), the positioning operation finishes. What is the causal f...

This was probably caused by one of the following two factors_ (1) ±OT is set to 'Disabled' in the parameter setting of the positioning control module (Type_... Show Detail
- No：1575
- Displayed Date：2023/04/25 19:00
- Category： Function

181-190 of Total 235

SPH

I/O
Error

Support tool

Info & News

To Top of Page

PKSHA FAQ logo

SPH

Regional Websites

About Us

Products & Solutions

Investor Relations

Sustainability