The SX bus connector of the SPH300EX (Type_ NP1PS-74D) is an OUT (output) connector. When you connect SX bus equipment,

You can use it as a standard base board by setting its station No. to '00.' In this case, you also need to set the syste

The equivalent data is retained for one default task during switching and the standby CPU starts execution from the begi

The simulation function of the StandardV3 does not support the index register. Check the program operation using a har

The Loader command mode is fixed to the TCP/IP communication. UDP/IP communication is not supported.

When the EMG signal and ±OT signal are not used, connect them to 24 V DC. Alternatively, you can set the ±OT signal to

Unfortunately, information in a device connected to the master module cannot be read even by building a user application

It occurs when any of the overrun, parity and framing errors is detected in the serial port of a general-purpose communi

If the start bit remains on, the positioning end signal is not generated.

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC > SPH

Latest FAQ

When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
When I attempted to download a project to a CPU with user ROM card by using D300win, a message appeared saying 'Invalid loader command process!' an...

GLOBAL

Search by category

Keyword Search

FAQ within [ SPH ]

151-160 of Total 235

≪ 16 / 24page ≫

The SPH300EX (Type_ NP1PS-74D) has an SX bus connector. Which ports should I use when connecting the SX bus cable to the SX bus expansion base, 'IN...

The SX bus connector of the SPH300EX (Type_ NP1PS-74D) is an OUT (output) connector. When you connect SX bus equipment, connect the cable to the IN (input)... Show Detail
- No：1535
- Displayed Date：2023/04/25 19:00
- Category： Main unit
Can I use a base board with station No. setup function (Type_ NP1B*-**S) as a standard base board (without 'S' at the end of type code)?

You can use it as a standard base board by setting its station No. to '00.' In this case, you also need to set the system definition of the loader designed f... Show Detail
- No：1531
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:50
- Category： Main unit
How does the redundant system handle tasks being executed when the operation is switched from an operating CPU to a standby CPU?

The equivalent data is retained for one default task during switching and the standby CPU starts execution from the beginning of the task. Show Detail
- No：1530
- Displayed Date：2023/04/25 19:00
- Category： Main unit
Can I use both P-link and PE-link in one system?

No, you cannot. Show Detail
- No：1523
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
I converted an M/F program into an SX program with the Standard loader. I performed simulation of the converted program in the Standard loader, but...

The simulation function of the StandardV3 does not support the index register. Check the program operation using a hardware PLC. Show Detail
- No：1471
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
I use the Ethernet module (Type_ NP1L-ET1/ET2) in the Loader command mode. Can I also use the UDP/IP communication?

The Loader command mode is fixed to the TCP/IP communication. UDP/IP communication is not supported. Show Detail
- No：1442
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
Please tell me the wiring method for the positioning control module (Type_ NP1F-MP2/MA2) when the EMG signal and ±OT signal are not used.

When the EMG signal and ±OT signal are not used, connect them to 24 V DC. Alternatively, you can set the ±OT signal to 'Disabled' in the parameter settings ... Show Detail
- No：1432
- Displayed Date：2023/04/25 19:00
- Category： Function
Is there any way to check the vendor ID, product code, product revision, serial No., etc. of the slave from the DeviceNet master module (Type_ NP1L...

Unfortunately, information in a device connected to the master module cannot be read even by building a user application. Please use the dedicated configura... Show Detail
- No：1387
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
With the general-purpose communication module (Type_ NP1L-RS□), in what cases does 'C0_ Hardware error detected during receiving' occur?

It occurs when any of the overrun, parity and framing errors is detected in the serial port of a general-purpose communication module. Show Detail
- No：1328
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
With the pulse train output positioning control module (Type_ NP1F-HP2), positioning has ended but the end signal is not generated.

If the start bit remains on, the positioning end signal is not generated. Show Detail
- No：1317
- Displayed Date：2023/04/25 19:00
- Category： Function

151-160 of Total 235

SPH

I/O
Error

Support tool

Info & News

To Top of Page

PKSHA FAQ logo

SPH

Regional Websites

About Us

Products & Solutions

Investor Relations

Sustainability