-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
- When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
- Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
- When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
- When I attempted to download a project to a CPU with user ROM card by using D300win, a message appeared saying 'Invalid loader command process!' an...
GLOBAL
Search by category
Keyword Search
FAQ within [ SPH ]
-
T-link or other expansion bases cannot be added by the SX bus. Show Detail
- No：1394
- Displayed Date：2023/04/25 19:00
- Category： Communication (T-link)
-
How many units of Ethernet module (Type_ NP1L-ET□) can be used in a system?
Up to 4 units can be connected in 1 configuration (on 1 SX bus). Note, however, that they must be configured so that the total number of units of other comm... Show Detail
- No：1395
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
-
The simulation function of the StandardV3 does not support the index register. Check the program operation using a hardware PLC. Show Detail
- No：1471
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
-
How can I use the pulse count function of the high-speed input module (Type_NP1X3206-A)?
We offer the sample program using the pulse count function for the high-speed input module. You can download the sample program and How-to Guide for it from... Show Detail
- No：1483
- Displayed Date：2023/04/25 19:00
- Category： Main unit
-
Usually, set the CPU No. to 0. The CPU No. 0 works as a master of an SX bus system. In a multi-CPU system or a CPU redundant system which uses multiple CPU ... Show Detail
- No：1504
- Displayed Date：2023/04/25 19:00
- Category： Main unit
-
No, it does not support multicast transmission (sending/receiving). It does support broadcast transmission (sending/receiving). Show Detail
- No：1536
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
-
Pulse output completion is indicated by the 'Command pulse zero' signal. Normally, it is '1' to indicate the status of completion. When the number of pulses... Show Detail
- No：1548
- Displayed Date：2023/04/25 19:00
- Category： Function
-
Can I use a commercial LAN cable for the SX bus instead of the dedicated cable?
No, you can't. Although the connection of the sending/receiving wires of the SX bus cable is the same as that for a commercial LAN cable (cross), the dedica... Show Detail
- No：1557
- Displayed Date：2023/04/25 19:00
- Category： Accessory
-
This problem was probably caused by the following factors_ (1) Failed contact of the connector on the SPH, (2) Failed contact on the POD (UG), (3) Improp... Show Detail
- No：1559
- Displayed Date：2023/04/25 19:00
- Category： Communication (T-link)
-
No, you can't. The relationship between i, which is the sensor output current, and i1 and i2, which are the CH input currents of the PLC, is expressed as i ... Show Detail
- No：1603
- Displayed Date：2023/04/25 19:00
- Category： I/O
151-160 of Total 235