The standard MICREX-SX SPH models have been designed for use in tropical wetlands. Therefore, all you need to do is to

After changing the range with the rotary switch, turn off the power once and then turn it on again, and the software off

The measurement accuracy does not include zero junction compensation accuracy. The zero junction compensation accuracy

When station number '0' is set on the servo, the station number set on the loader becomes effective. If, however, you w

Once an error history is generated, it is retained internally within the FL-net module and is cleared when the power is

Yes, a CPU is necessary. In the case of a system with no CPU, the input status LED does not work even if signals are ext

You can use it as a standard base board by setting its station No. to '00.' In this case, you also need to set the syste

Do not install an I/O terminal (Type_NR1S*-*, NR1T*-*, NR1J*-*, and NR1D*-*) on the floor of the panel because it has no

Yes, it is possible. Note that one relay causes attenuation of about 1 dB. The allowable attenuation is 7 dB in total.

T-link or other expansion bases cannot be added by the SX bus.

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC > SPH

Latest FAQ

When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
When I attempted to download a project to a CPU with user ROM card by using D300win, a message appeared saying 'Invalid loader command process!' an...

GLOBAL

Search by category

Keyword Search

FAQ within [ SPH ]

141-150 of Total 235

≪ 15 / 24page ≫

I want MICREX-SX SPH models adapted to tropical wetlands.

The standard MICREX-SX SPH models have been designed for use in tropical wetlands. Therefore, all you need to do is to order standard models. Show Detail
- No：1287
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 14:17
- Category： Others
When I set offset on the analog module (NP1AXH8I-MR) by using software (parameters) and disable the software offset setting by operating hardware (...

After changing the range with the rotary switch, turn off the power once and then turn it on again, and the software offset setting will be disabled. Show Detail
- No：1667
- Displayed Date：2023/04/25 19:00
- Category： I/O
Does the accuracy specification of the thermocouple input module (Type_ NP1AXH4-TC) include zero junction compensation accuracy?

The measurement accuracy does not include zero junction compensation accuracy. The zero junction compensation accuracy is ±1°C (at ambient temperature 0°C ... Show Detail
- No：1597
- Displayed Date：2023/04/25 19:00
- Category： I/O
The system using a servo directly connected to the SX bus does not start. I confirmed that the system configuration definition is correct.

When station number '0' is set on the servo, the station number set on the loader becomes effective. If, however, you want to use the servo for fail-soft st... Show Detail
- No：1594
- Displayed Date：2023/04/25 19:00
- Category： Others
How does the FL-net module (Type_ NP1L-FL1/FL2/FL3) clear the error history recorded in each memory?

Once an error history is generated, it is retained internally within the FL-net module and is cleared when the power is turned off and turned on again or whe... Show Detail
- No：1567
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
Is a CPU necessary to check I/O? Input signals to the input terminals of an input module are turned ON, however, the input status LED remains OFF.

Yes, a CPU is necessary. In the case of a system with no CPU, the input status LED does not work even if signals are externally input into the input module. Show Detail
- No：1537
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
Can I use a base board with station No. setup function (Type_ NP1B*-**S) as a standard base board (without 'S' at the end of type code)?

You can use it as a standard base board by setting its station No. to '00.' In this case, you also need to set the system definition of the loader designed f... Show Detail
- No：1531
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:50
- Category： Main unit
Can I install an I/O terminal (Type_NR1S*-*, NR1T*-*, NR1J*-*, and NR1D*-*) in the vertical direction on the panel?

Do not install an I/O terminal (Type_NR1S*-*, NR1T*-*, NR1J*-*, and NR1D*-*) on the floor of the panel because it has no ventilation slit for cooling. You ca... Show Detail
- No：1520
- Displayed Date：2023/04/25 19:00
- Category： I/O
I want to relay the SX bus optical cable. Is it possible?

Yes, it is possible. Note that one relay causes attenuation of about 1 dB. The allowable attenuation is 7 dB in total. Careful consideration is required be... Show Detail
- No：1429
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
I want to expand the T-link expansion (T-link interface module Type_ NP1L-RT1) by further adding a base. Can I do this expansion by using the SX bus?

T-link or other expansion bases cannot be added by the SX bus. Show Detail
- No：1394
- Displayed Date：2023/04/25 19:00
- Category： Communication (T-link)