-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
- When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
- Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
- When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
- When I attempted to download a project to a CPU with user ROM card by using D300win, a message appeared saying 'Invalid loader command process!' an...
GLOBAL
Search by category
Keyword Search
FAQ within [ SPH ]
-
With a general-purpose communication module, is RS232C completely full duplex?
It is full duplex for both hardware and software (firmware) for anything other than communication by M_RECEIVE and M_SEND on the SX bus, which are FB interna... Show Detail
- No：1413
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
The Loader command mode is fixed to the TCP/IP communication. UDP/IP communication is not supported. Show Detail
- No：1442
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
-
The MICREX-SX series positioning module 'Type_NP1F-HD2A' replaces NC1F-VP1/FGU130B. Be aware of the following points: 1) NP1F-HD2A is differential output t... Show Detail
- No：1463
- Displayed Date：2023/04/25 19:00
- Category： Function
-
Are there any FL-net boards compatible with Windows 10?
※NP3L-FL3PXSの英文マニュアルなし。FAQの翻訳は実施したので、有効フラグOFFにして登録のみ実施。英文マニュアルを作った場合、公開する。（2021/1/22：光井、小笠原） NP3L-FL3PXS (PCI-Express-bus-based FL-net board) is compatible ... Show Detail
- No：1464
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
I use Expert (D300win). Can I check the download history to the CPU?
When downloading a project (including Patch POU), you can save the download history in your personal computer or the CPU module. [Setting procedure] ・In t... Show Detail
- No：1490
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
-
What is the type of the configurator that is used with NP1L-PD1/PD2?
Use the following types of configurators: 'CONF-PDP' for NP1L-PD1 and 'NetTool for Profibus' for NP1L-PD2. Purchase a configurator from HMS Industrial Networ... Show Detail
- No：1494
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
In the standard expansion counter FB _MHCNTH, CH0 operates but CH1 does not.
It seems that this problem was caused by an improper address setting for INDAT/OUTDAT assigned to the counter FB terminal. On a single module, assign the sa... Show Detail
- No：1539
- Displayed Date：2023/04/25 19:00
- Category： Function
-
In exponentiation operation, when a negative value is used for the base, the result is 0. Show Detail
- No：1551
- Displayed Date：2023/04/25 19:00
- Category： Application
-
No, the Ethernet module does not support the AUTO-MDI/MDIX function (Auto-switching of straight/cross cable.) The applicable cable type depends on whether ... Show Detail
- No：1562
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
-
A nonfatal fault of the takt cycle monitoring error has occurred. What is a possible cause?
The takt cycle monitoring error is caused by the following factors_ (1) The preset takt cycle value specified in the system definition is shorter than the ac... Show Detail
- No：1576
- Displayed Date：2023/04/25 19:00
- Category： Error
141-150 of Total 235