When the CPU module is stopped, the positioning operation stops.

Yes, you can. Note, however, that the input impedance reduces to half. Pay attention to the drive ability of the sensor.

You should be careful because if the write protection is OFF, the ROM is rewritten simultaneously with the internal RAM

The IP address and port standard No. of the self station of the Ethernet module are stored in the internal ROM of the Et

No, they do not have polarity because they use relay contacts.

Proportional band P is the % of the variation range of input PV required for the change of output MV in the effective va

Move to the item ID without using the access path on the client side (D_).

The influence of external resistance on the thermocouple input is approximately 0.3 ?V/?. The measurement accuracy of t

You can use it provided that the system is a single-unit system (configured with one base only). Connect the connectors

Yes, a CPU is necessary. In the case of a system with no CPU, the input status LED does not work even if signals are ext

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC > SPH

Latest FAQ

When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
When I attempted to download a project to a CPU with user ROM card by using D300win, a message appeared saying 'Invalid loader command process!' an...

GLOBAL

Search by category

Keyword Search

FAQ within [ SPH ]

131-140 of Total 235

≪ 14 / 24page ≫

When I switch the CPU module from RUN to STOP while the four-axis pulse output unit (NR1SF-HP4DT) is outputting pulses, does the positioning operat...

When the CPU module is stopped, the positioning operation stops. Show Detail
- No：1669
- Displayed Date：2023/04/25 19:00
- Category： Function
I will use the analog voltage input module. Can I input a single input signal to two CHs of the module simultaneously (in parallel) to use them?

Yes, you can. Note, however, that the input impedance reduces to half. Pay attention to the drive ability of the sensor. Show Detail
- No：1622
- Displayed Date：2023/04/25 19:00
- Category： I/O
When I mount the user ROM card for the SPH200 (Type_ NP8PMF-16) without changing its write protection from OFF, is the content of the ROM protected?

You should be careful because if the write protection is OFF, the ROM is rewritten simultaneously with the internal RAM of the CPU during program download. Show Detail
- No：1617
- Displayed Date：2023/04/25 19:00
- Category： Main unit
After I replaced an Ethernet module (Type_NP1L-ET1/ET2), it cannot communicate with the target device. What is a possible cause?

The IP address and port standard No. of the self station of the Ethernet module are stored in the internal ROM of the Ethernet module. After replacing an Eth... Show Detail
- No：1590
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
Do the blue and white cables for the ALM output of the power supply module (Type_ NP1S-22) have polarity?

No, they do not have polarity because they use relay contacts. Show Detail
- No：1585
- Displayed Date：2023/04/25 19:00
- Category： Main unit
In PPID, a POU for the PID FB package, which range does the % of proportional band P account for?

Proportional band P is the % of the variation range of input PV required for the change of output MV in the effective variation range from 0 to 100%. It is... Show Detail
- No：1580
- Displayed Date：2023/04/25 19:00
- Category： Function
When I use the SX communication middleware (Type_ NP4N-MDLW) and specify (_) in the access path during the item registration for the client, Errno=...

Move to the item ID without using the access path on the client side (D_). Show Detail
- No：1556
- Displayed Date：2023/04/25 19:00
- Category： Support tool
Is the measurement accuracy affected when an external arrestor for protection is mounted on the input terminal of the thermocouple input module (Ty...

The influence of external resistance on the thermocouple input is approximately 0.3 ?V/?. The measurement accuracy of the thermocouple input is affected by... Show Detail
- No：1545
- Displayed Date：2023/04/25 19:00
- Category： I/O
I don't have the SX bus loop-back plug (Type_ NP8B-BP). Can I use the SX bus cable instead?

You can use it provided that the system is a single-unit system (configured with one base only). Connect the connectors at both ends of the cable to IN and ... Show Detail
- No：1543
- Displayed Date：2023/04/25 19:00
- Category： Accessory
Is a CPU necessary to check I/O? Input signals to the input terminals of an input module are turned ON, however, the input status LED remains OFF.

Yes, a CPU is necessary. In the case of a system with no CPU, the input status LED does not work even if signals are externally input into the input module. Show Detail
- No：1537
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)

131-140 of Total 235

SPH

I/O
Error

Support tool

Info & News

To Top of Page

PKSHA FAQ logo

SPH

Regional Websites

About Us

Products & Solutions

Investor Relations

Sustainability