While 'DTR_ terminal ready' can be used with RS-232C, this control line is not present for RS-485. If no response is re

There is a limit to the number of words for the I/O modules that can be mounted on a T-link expansion (Type_ NP1L-RT1) b

The P-link memory is prepared in the P-link module. It is separate from the memory in the CPU and no change takes place

In an SX system, removing any I/O module that has failed causes the CPU to stop running due to a 'system definition mism

If the CPU modules are mounted on a hot plug base board with station No. setup function, you can replace them without tu

Set the port No. as described below. (1) For NP1L-RS2_ Set '0.' (2) For NP1L-RS4_ Set '1.' See the figure below for th

The redundant function of the SPH Series provides redundancy only for the CPU and it cannot make the Ethernet redundant.

Up to 4 units can be connected in 1 configuration (on 1 SX bus). Note, however, that they must be configured so that th

You can order sulfurized gas-resistant models by adding /Z4 at the end of product type code of the MICREX-SX SPH. Or, co

The memory usage is displayed in 'GM (global memory)' by the 'Device' function that is used to edit tags or check the m

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC > SPH

Latest FAQ

When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
When I attempted to download a project to a CPU with user ROM card by using D300win, a message appeared saying 'Invalid loader command process!' an...

GLOBAL

Search by category

Keyword Search

FAQ within [ SPH ]

131-140 of Total 235

≪ 14 / 24page ≫

With communication using RS-485 of a general-purpose communication module (Type_ NP1L-RS□), is there any means to detect a line disconnection?

While 'DTR_ terminal ready' can be used with RS-232C, this control line is not present for RS-485. If no response is received while data are exchanged, re... Show Detail
- No：1322
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:20
- Category： Communication (Others)
I attempted to register 10 units of thermocouple input module (Type_ NP1AXH4-TC) on the T-link expansion (Type_ NP1L-RT1) base but it was not possi...

There is a limit to the number of words for the I/O modules that can be mounted on a T-link expansion (Type_ NP1L-RT1) base_ 128. With the thermocouple inpu... Show Detail
- No：1333
- Displayed Date：2023/04/25 19:00
- Category： Communication (T-link)
In a redundant system, what will happen to the P-link memory at the time of switchover to a standby CPU?

The P-link memory is prepared in the P-link module. It is separate from the memory in the CPU and no change takes place at the time of switchover to a standb... Show Detail
- No：1343
- Displayed Date：2023/04/25 19:00
- Category： Main unit
What is the dummy module (Type_ NP1F-DMY) used for? Is it required for an unused slot?

In an SX system, removing any I/O module that has failed causes the CPU to stop running due to a 'system definition mismatch.' In a case like this, a dummy ... Show Detail
- No：1349
- Displayed Date：2023/04/25 19:00
- Category： Function
When redundant CPUs mounted on the same base board break down, can I replace the CPU without turning off the power?

If the CPU modules are mounted on a hot plug base board with station No. setup function, you can replace them without turning off the power. Show Detail
- No：1367
- Displayed Date：2023/04/25 19:00
- Category： Main unit
For the initial setting of a general-purpose communication module with only one communication port such as NP1L-RS2 and NP1L-RS4, is it correct to ...

Set the port No. as described below. (1) For NP1L-RS2_ Set '0.' (2) For NP1L-RS4_ Set '1.' See the figure below for the setting for each type of genera... Show Detail
- No：1383
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:45
- Category： Communication (Others)
Is it possible to have redundant (duplicate) Ethernet communication via the Ethernet interface module (Type_ NP1L-ET1/ET2) in a redundant system of...

The redundant function of the SPH Series provides redundancy only for the CPU and it cannot make the Ethernet redundant. Show Detail
- No：1392
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
How many units of Ethernet module (Type_ NP1L-ET□) can be used in a system?

Up to 4 units can be connected in 1 configuration (on 1 SX bus). Note, however, that they must be configured so that the total number of units of other comm... Show Detail
- No：1395
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
I want MICREX-SX SPH models designed to resist sulfurized gas.

You can order sulfurized gas-resistant models by adding /Z4 at the end of product type code of the MICREX-SX SPH. Or, contact your Fuji Electric sales repres... Show Detail
- No：1425
- Displayed Date：2023/04/25 19:00
- Category： Others
On the StandardV3 loader, the memory usage of a processor link module such as a P/PE-link or FL-net module cannot be displayed. Can I check the mem...

The memory usage is displayed in 'GM (global memory)' by the 'Device' function that is used to edit tags or check the memory usage. However, the memory cap... Show Detail
- No：1484
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)