Set the I/O area of the positioning module following the steps below. 1) Set 'h1C00' in the offset word address +16 (Ch1

If the CPU modules are mounted on a hot plug base board with station No. setup function, you can replace them without tu

There is a high-capacity battery for SPH300 (Type_ NP8P-BTS). Its battery capacity (approximately 2700 mA) is about 2.7

In an SX system, removing any I/O module that has failed causes the CPU to stop running due to a 'system definition mism

Only when the MICREX-F CPU is F55/F70/F70S/F80H/F120H/F120S to F150S, you can connect a MICREX-SX series T-link interfac

In Standard loader, to access the input memory from MONITOUCH, cancel the I/O group setting of the input specified as 'n

The cable is not oil resistant so that you need to protect it by covering it with oil-resistant material.

You cannot mount the following I/O modules_ (1) High-speed input module NP1X3206-A, (2) High-speed output module NP1Y32

The bus can be extended with the SX bus electrical repeater (Type_ NP2L-RP1). Up to three repeaters can be used in one

The simulation function of the StandardV3 does not support the index register. Check the program operation using a har

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC > SPH

Latest FAQ

When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
When I attempted to download a project to a CPU with user ROM card by using D300win, a message appeared saying 'Invalid loader command process!' an...

GLOBAL

Search by category

Keyword Search

FAQ within [ SPH ]

121-130 of Total 235

≪ 13 / 24page ≫

How do I use a manual pulse generator with the positioning module (Type_NP1F-MP2/MA2)?

Set the I/O area of the positioning module following the steps below. 1) Set 'h1C00' in the offset word address +16 (Ch1 Set value area: Low word). (Set ... Show Detail
- No：1396
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:17
- Category： Function
When redundant CPUs mounted on the same base board break down, can I replace the CPU without turning off the power?

If the CPU modules are mounted on a hot plug base board with station No. setup function, you can replace them without turning off the power. Show Detail
- No：1367
- Displayed Date：2023/04/25 19:00
- Category： Main unit
Is there a battery available with a longer backup time than the backup battery for SPH (Type_ NP8P-BT)?

There is a high-capacity battery for SPH300 (Type_ NP8P-BTS). Its battery capacity (approximately 2700 mA) is about 2.7 times that of the backup battery supp... Show Detail
- No：1360
- Displayed Date：2023/04/25 19:00
- Category： Accessory
What is the dummy module (Type_ NP1F-DMY) used for? Is it required for an unused slot?

In an SX system, removing any I/O module that has failed causes the CPU to stop running due to a 'system definition mismatch.' In a case like this, a dummy ... Show Detail
- No：1349
- Displayed Date：2023/04/25 19:00
- Category： Function
Can I connect a MICREX-SX series T-link interface module (Type_NP1L-RT1) to a MICREX-F series T-link master module?

Only when the MICREX-F CPU is F55/F70/F70S/F80H/F120H/F120S to F150S, you can connect a MICREX-SX series T-link interface module although the order of the bi... Show Detail
- No：1277
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:08
- Category： Communication (T-link)
To debug a PLC program without I/O module, I set I/Os as 'no equipment'. Then, I tried to set input contact (X) using switch of MONITOUCH. However,...

In Standard loader, to access the input memory from MONITOUCH, cancel the I/O group setting of the input specified as 'no equipment.' If the input specified... Show Detail
- No：1658
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 14:04
- Category： Support tool (Standard)
Is the SX bus cable oil resistant?

The cable is not oil resistant so that you need to protect it by covering it with oil-resistant material. Show Detail
- No：1604
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
Are there any I/O modules that cannot be mounted on the T-link expansion base?

You cannot mount the following I/O modules_ 　(1) High-speed input module NP1X3206-A, (2) High-speed output module NP1Y32T09P1-A, (3) Analog input module NP... Show Detail
- No：1577
- Displayed Date：2023/04/25 19:00
- Category： Communication (T-link)
The total extension of the SX bus has exceeded 25 m. Is there anything to relay the connection?

The bus can be extended with the SX bus electrical repeater (Type_ NP2L-RP1). Up to three repeaters can be used in one system. (When three repeaters are us... Show Detail
- No：1550
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
I converted an M/F program into an SX program with the Standard loader. I performed simulation of the converted program in the Standard loader, but...

The simulation function of the StandardV3 does not support the index register. Check the program operation using a hardware PLC. Show Detail
- No：1471
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)