When connected via 10BASE-T, you can replace it. There is no need to change the system definition. Before replacement, s

The equivalent data is retained for one default task during switching and the standby CPU starts execution from the begi

A 'client' is a device that collects data. Since the PLC is a device from which data is collected, there is no OPC clien

No, you can't. Although the connection of the sending/receiving wires of the SX bus cable is the same as that for a com

Filter instructions are system FBs. System FBs that can be equalized are limited to_ The last value of the edge detectio

No, you can't. The relationship between i, which is the sensor output current, and i1 and i2, which are the CH input cu

The backup battery is intended to back up the data memory (SRAM) inside of the CPU. While the system is turned on, the p

The data written with the F_WRITE FB is in a binary format. Consequently, it can be manipulated with commercial binary e

There is a possibility of mismatch between the project in the user ROM card and the CPU memory. On the 'Failure diagnosi

One possibility is that the compare value is not stored in the compare register of the high-speed counter. The compare v

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC > SPH

Latest FAQ

When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
When I attempted to download a project to a CPU with user ROM card by using D300win, a message appeared saying 'Invalid loader command process!' an...

GLOBAL

Search by category

Keyword Search

FAQ within [ SPH ]

121-130 of Total 235

≪ 13 / 24page ≫

Can I replace NP1L-FL2 with NP1L-FL3 for FL-net communication?

When connected via 10BASE-T, you can replace it. There is no need to change the system definition. Before replacement, set the switches on the front of the N... Show Detail
- No：1524
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
How does the redundant system handle tasks being executed when the operation is switched from an operating CPU to a standby CPU?

The equivalent data is retained for one default task during switching and the standby CPU starts execution from the beginning of the task. Show Detail
- No：1530
- Displayed Date：2023/04/25 19:00
- Category： Main unit
There is an OPC server that supports the MICREX-SX (communication middleware, Type_ NP4N-MDLW). Is there an OPC client?

A 'client' is a device that collects data. Since the PLC is a device from which data is collected, there is no OPC client. Show Detail
- No：1553
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
Can I use a commercial LAN cable for the SX bus instead of the dedicated cable?

No, you can't. Although the connection of the sending/receiving wires of the SX bus cable is the same as that for a commercial LAN cable (cross), the dedica... Show Detail
- No：1557
- Displayed Date：2023/04/25 19:00
- Category： Accessory
I want to equalize filter instructions in a redundant system.

Filter instructions are system FBs. System FBs that can be equalized are limited to_ The last value of the edge detection FB, present counter value of the co... Show Detail
- No：1563
- Displayed Date：2023/04/25 19:00
- Category： Application
I will use the analog current input module. Can I input a single input signal to two CHs of the module simultaneously (in parallel) to use them?

No, you can't. The relationship between i, which is the sensor output current, and i1 and i2, which are the CH input currents of the PLC, is expressed as i ... Show Detail
- No：1603
- Displayed Date：2023/04/25 19:00
- Category： I/O
Is the backup battery consumed while the control power supply of the CPU is active?

The backup battery is intended to back up the data memory (SRAM) inside of the CPU. While the system is turned on, the power is supplied from the control pow... Show Detail
- No：1621
- Displayed Date：2023/04/25 19:00
- Category： Accessory
Is it possible to use a PC application program to manipulate data that was written with the SX application (F_WRITE) onto the memory card inserted ...

The data written with the F_WRITE FB is in a binary format. Consequently, it can be manipulated with commercial binary editors. Show Detail
- No：1623
- Displayed Date：2023/04/25 19:00
- Category： Application
I attempted to clear the memory in a CPU with the 'Clear' command for online operations, however, I got a message saying 'Clearing failed' and coul...

There is a possibility of mismatch between the project in the user ROM card and the CPU memory. On the 'Failure diagnosis' dialog, check the 'Resource inform... Show Detail
- No：1660
- Displayed Date：2023/04/25 19:00
- Category： Support tool
I use the high-speed counter module (Type_ NP1F-HC2) FB. The compare value is larger than the present counter value but the compare output becomes ...

One possibility is that the compare value is not stored in the compare register of the high-speed counter. The compare value is written by turning the data w... Show Detail
- No：1309
- Displayed Date：2023/04/25 19:00
- Category： Function