Only when the MICREX-F CPU is F55/F70/F70S/F80H/F120H/F120S to F150S, you can connect a MICREX-SX series T-link interfac

In an SX system, removing any I/O module that has failed causes the CPU to stop running due to a 'system definition mism

There is a high-capacity battery for SPH300 (Type_ NP8P-BTS). Its battery capacity (approximately 2700 mA) is about 2.7

If the CPU modules are mounted on a hot plug base board with station No. setup function, you can replace them without tu

Set the I/O area of the positioning module following the steps below. 1) Set 'h1C00' in the offset word address +16 (Ch1

The file transfer error occurs because the module driver is downloaded with the Ethernet module not recognized by the CP

The following are necessary. 1) Hardware: General-purpose communication module (NP1L-RS1/RS2/RS3/RS4/RS5) whose fi

The general-purpose communication function of Ethernet allows simplified broadcast communication. By using a CPU with b

Use the following types of configurators: 'CONF-PDP' for NP1L-PD1 and 'NetTool for Profibus' for NP1L-PD2. Purchase a co

RS-485 is upper compatible with RS-422. In general, RS-422 devices mainly use 4-wire connection method, while RS-485 dev

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC > SPH

Latest FAQ

When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
When I attempted to download a project to a CPU with user ROM card by using D300win, a message appeared saying 'Invalid loader command process!' an...

GLOBAL

Search by category

Keyword Search

FAQ within [ SPH ]

111-120 of Total 235

≪ 12 / 24page ≫

Can I connect a MICREX-SX series T-link interface module (Type_NP1L-RT1) to a MICREX-F series T-link master module?

Only when the MICREX-F CPU is F55/F70/F70S/F80H/F120H/F120S to F150S, you can connect a MICREX-SX series T-link interface module although the order of the bi... Show Detail
- No：1277
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:08
- Category： Communication (T-link)
What is the dummy module (Type_ NP1F-DMY) used for? Is it required for an unused slot?

In an SX system, removing any I/O module that has failed causes the CPU to stop running due to a 'system definition mismatch.' In a case like this, a dummy ... Show Detail
- No：1349
- Displayed Date：2023/04/25 19:00
- Category： Function
Is there a battery available with a longer backup time than the backup battery for SPH (Type_ NP8P-BT)?

There is a high-capacity battery for SPH300 (Type_ NP8P-BTS). Its battery capacity (approximately 2700 mA) is about 2.7 times that of the backup battery supp... Show Detail
- No：1360
- Displayed Date：2023/04/25 19:00
- Category： Accessory
When redundant CPUs mounted on the same base board break down, can I replace the CPU without turning off the power?

If the CPU modules are mounted on a hot plug base board with station No. setup function, you can replace them without turning off the power. Show Detail
- No：1367
- Displayed Date：2023/04/25 19:00
- Category： Main unit
How do I use a manual pulse generator with the positioning module (Type_NP1F-MP2/MA2)?

Set the I/O area of the positioning module following the steps below. 1) Set 'h1C00' in the offset word address +16 (Ch1 Set value area: Low word). (Set ... Show Detail
- No：1396
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:17
- Category： Function
When I use an Ethernet module (Type_ NP1L-ET□) to download the system definitions and module driver, a file transfer error is generated. Why?

The file transfer error occurs because the module driver is downloaded with the Ethernet module not recognized by the CPU. For the CPU to recognize the Ethe... Show Detail
- No：1404
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
What is necessary for MODBUS_RTU communication between SPH and an external device?

The following are necessary. 1) Hardware: General-purpose communication module (NP1L-RS1/RS2/RS3/RS4/RS5) whose firmware version is V42 or later ... Show Detail
- No：1469
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:29
- Category： Communication (Others)
Can I perform broadcast communication between CPU modules without using FL-net or P/PE-link module?

The general-purpose communication function of Ethernet allows simplified broadcast communication. By using a CPU with built-in Ethernet, you can build a bro... Show Detail
- No：1485
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
What is the type of the configurator that is used with NP1L-PD1/PD2?

Use the following types of configurators: 'CONF-PDP' for NP1L-PD1 and 'NetTool for Profibus' for NP1L-PD2. Purchase a configurator from HMS Industrial Networ... Show Detail
- No：1494
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
What is the difference between RS-485 and RS-422 ?

RS-485 is upper compatible with RS-422. In general, RS-422 devices mainly use 4-wire connection method, while RS-485 devices mainly use 2-wire connection met... Show Detail
- No：1521
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)