Refer to the following How-to Guide, which describes how to update a program while a redundant system is running. MICRE

In MICREX-SX, a scan list is automatically created by registering the remote I/O to be connected to the master module in

It is possible by preparing two types of power supply for driving the transistor device and the load. Refer to the User

One possible cause is that common FB _C_COM is not registered with the library. For communication-related expansion FBs

Yes, all points can be used. Regarding the pulse width, pulse signals with a width down to 20 us can be captured with po

One possibility is that the compare value is not stored in the compare register of the high-speed counter. The compare v

There is a possibility of mismatch between the project in the user ROM card and the CPU memory. On the 'Failure diagnosi

The data written with the F_WRITE FB is in a binary format. Consequently, it can be manipulated with commercial binary e

The backup battery is intended to back up the data memory (SRAM) inside of the CPU. While the system is turned on, the p

No, you can't. The relationship between i, which is the sensor output current, and i1 and i2, which are the CH input cu

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC > SPH

Latest FAQ

When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
When I attempted to download a project to a CPU with user ROM card by using D300win, a message appeared saying 'Invalid loader command process!' an...

GLOBAL

Search by category

Keyword Search

FAQ within [ SPH ]

101-110 of Total 235

≪ 11 / 24page ≫

In a CPU redundant system, how can I update a program while the system is running?

Refer to the following How-to Guide, which describes how to update a program while a redundant system is running. MICREX SX How-to Guide 'How to Change Prog... Show Detail
- No：1352
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
With the DeviceNet master module (Type_ NP1L-DN1), how can I create a scan list and register it with the master module?

In MICREX-SX, a scan list is automatically created by registering the remote I/O to be connected to the master module in the system configuration definitions... Show Detail
- No：1346
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:35
- Category： Communication (Others)
Is it possible to use a transistor output module (12 to 24 V DC model) of the SPH Series at a load voltage lower than the rated voltage?

It is possible by preparing two types of power supply for driving the transistor device and the load. Refer to the User's Guide, which provides explanatio... Show Detail
- No：1331
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:32
- Category： I/O
With D300win, I used a non-procedural FB (_C_free) in a program for compilation and an error occurred. What is the cause of this problem?

One possible cause is that common FB _C_COM is not registered with the library. For communication-related expansion FBs including _C_FREE, register common... Show Detail
- No：1329
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:32
- Category： Communication (Others)
When the pulse catch function of the high-speed input module (Type_ NP1X3206-A) is used, can all points be used? Is any difference made to the puls...

Yes, all points can be used. Regarding the pulse width, pulse signals with a width down to 20 us can be captured with ports 1 to 8. With ports 9 to 32, pu... Show Detail
- No：1321
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:17
- Category： Function
I use the high-speed counter module (Type_ NP1F-HC2) FB. The compare value is larger than the present counter value but the compare output becomes ...

One possibility is that the compare value is not stored in the compare register of the high-speed counter. The compare value is written by turning the data w... Show Detail
- No：1309
- Displayed Date：2023/04/25 19:00
- Category： Function
I attempted to clear the memory in a CPU with the 'Clear' command for online operations, however, I got a message saying 'Clearing failed' and coul...

There is a possibility of mismatch between the project in the user ROM card and the CPU memory. On the 'Failure diagnosis' dialog, check the 'Resource inform... Show Detail
- No：1660
- Displayed Date：2023/04/25 19:00
- Category： Support tool
Is it possible to use a PC application program to manipulate data that was written with the SX application (F_WRITE) onto the memory card inserted ...

The data written with the F_WRITE FB is in a binary format. Consequently, it can be manipulated with commercial binary editors. Show Detail
- No：1623
- Displayed Date：2023/04/25 19:00
- Category： Application
Is the backup battery consumed while the control power supply of the CPU is active?

The backup battery is intended to back up the data memory (SRAM) inside of the CPU. While the system is turned on, the power is supplied from the control pow... Show Detail
- No：1621
- Displayed Date：2023/04/25 19:00
- Category： Accessory
I will use the analog current input module. Can I input a single input signal to two CHs of the module simultaneously (in parallel) to use them?

No, you can't. The relationship between i, which is the sensor output current, and i1 and i2, which are the CH input currents of the PLC, is expressed as i ... Show Detail
- No：1603
- Displayed Date：2023/04/25 19:00
- Category： I/O