-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
- When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
- Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
- When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
- When I attempted to download a project to a CPU with user ROM card by using D300win, a message appeared saying 'Invalid loader command process!' an...
GLOBAL
Search by category
Keyword Search
FAQ within [ SPH ]
-
Use the 'Excitation timing output' signal for the Z-phase pulse when a stepping motor is used. Show Detail
- No：1574
- Displayed Date：2023/04/25 19:00
- Category： Function
-
Since the data equalization (data copying from the operating CPU to the standby CPU) is performed after the default task is processed, the larger the size of... Show Detail
- No：1568
- Displayed Date：2023/04/25 19:00
- Category： Main unit
-
Which mode does the Ethernet module (Type_ NP1L-ET1/ET2) support, half or full?
Only the NP1L-ET1 supports both modes automatically (auto negotiation). Since the NP1L-ET2 is designed for 10Base5 (coaxial), it is fixed to half duplex. Show Detail
- No：1554
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
-
The module counts feedback pulses even without Z-phase pulse signals. Note that when Z-phase pulse signals are not provided, origin return operation is dis... Show Detail
- No：1549
- Displayed Date：2023/04/25 19:00
- Category： Function
-
In the standard expansion counter FB _MHCNTH, CH0 operates but CH1 does not.
It seems that this problem was caused by an improper address setting for INDAT/OUTDAT assigned to the counter FB terminal. On a single module, assign the sa... Show Detail
- No：1539
- Displayed Date：2023/04/25 19:00
- Category： Function
-
The memory usage is displayed in 'GM (global memory)' by the 'Device' function that is used to edit tags or check the memory usage. However, the memory cap... Show Detail
- No：1484
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
-
I want MICREX-SX SPH models designed to resist sulfurized gas.
You can order sulfurized gas-resistant models by adding /Z4 at the end of product type code of the MICREX-SX SPH. Or, contact your Fuji Electric sales repres... Show Detail
- No：1425
- Displayed Date：2023/04/25 19:00
- Category： Others
-
How many units of Ethernet module (Type_ NP1L-ET□) can be used in a system?
Up to 4 units can be connected in 1 configuration (on 1 SX bus). Note, however, that they must be configured so that the total number of units of other comm... Show Detail
- No：1395
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
-
The redundant function of the SPH Series provides redundancy only for the CPU and it cannot make the Ethernet redundant. Show Detail
- No：1392
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
-
Set the port No. as described below. (1) For NP1L-RS2_ Set '0.' (2) For NP1L-RS4_ Set '1.' See the figure below for the setting for each type of genera... Show Detail
- No：1383
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:45
- Category： Communication (Others)
91-100 of Total 235