-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
- When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
- Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
- When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
- When I attempted to download a project to a CPU with user ROM card by using D300win, a message appeared saying 'Invalid loader command process!' an...
GLOBAL
Search by category
Keyword Search
FAQ within [ SPH ]
-
You can check it with the status indication LED on the front of the module. When a low battery voltage is detected, the CER LED on the front of the module ... Show Detail
- No：1620
- Displayed Date：2023/04/25 19:00
- Category： Function
-
The 'SND' and 'RCV' LEDs on the P-link module (Type_ NP1L-PL1) look dark. Is this a fault?
The LEDs of the P-link module (Type_ NP1L-PL1) are designed to blink quickly in accordance with the ON/OFF of a signal. Although they look dim to the human e... Show Detail
- No：1624
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
You can install only the USB driver afterwards. For V3.6.12.18 or later version of D300win, the USB driver can be installed at the time of installation of... Show Detail
- No：1285
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 14:16
- Category： Support tool (D300win)
-
The SPH system automatically inherits information such as the communication ports and reopening processing is not required. Show Detail
- No：1292
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
-
Selecting the DCE mode for the communication parameter_ DCE designation keeps DSR always on. Show Detail
- No：1297
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
Can I store multiple programs in the user ROM card (CF or SD) ?
No, it is not possible. Only one program can be stored. Show Detail
- No：1298
- Displayed Date：2023/04/25 19:00
- Category： Main unit
-
It is not possible with D300win V2. The sampling trace function is supported by D300win V3.1.1.0. or later. [Related document] Refer to Section '11-7 Sampl... Show Detail
- No：1310
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
-
No, it is not possible. Use an encoder of the line-driver or open-collector output type. When using a line-driver type, pay attention to the output capacity ... Show Detail
- No：1320
- Displayed Date：2023/04/25 19:00
- Category： Function
-
While 'DTR_ terminal ready' can be used with RS-232C, this control line is not present for RS-485. If no response is received while data are exchanged, re... Show Detail
- No：1322
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:20
- Category： Communication (Others)
-
Is it possible to use the optical converter NP1L-OL1 between processors as with the P-link?
The optical converter NP1L-OL1 is an optical converter of the SX bus. It cannot be used because the SX bus is not a link between processors. Show Detail
- No：1327
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:31
- Category： Communication (Others)
91-100 of Total 235