-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
- When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
- Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
- When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
- When I attempted to download a project to a CPU with user ROM card by using D300win, a message appeared saying 'Invalid loader command process!' an...
GLOBAL
Search by category
Keyword Search
FAQ within [ SPH ]
-
What is the difference between the LG and FG terminals of the power supply module (Type_ NP1S-22)?
The LG terminal is a line filter ground terminal in the power supply module. It is intended for guiding any external noise produced in the power supply or sw... Show Detail
- No：1374
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 10:52
- Category： Main unit
-
This warning appears when the memory (DL) that is assigned to file declaration created for the timer/counter current values overlaps with the DL memory that... Show Detail
- No：1653
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
-
One M_OPEN consumes one port of SPORT_NO, which is the local port. RPORT_NO is the port of the other end of the communication seen from the SX. Show Detail
- No：1643
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
-
For PID control by using a PID FB package, how should I set the various parameters?
For setting parameter values (such as P, I and D), it is possible to_ (1) Set the data within the user application (2) Use 'PID FB parameter support ut... Show Detail
- No：1296
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 14:18
- Category： Function
-
There are two ways to connect a USB port of a personal computer and a CPU: 1) Connect to the USB port of the CPU (directly connected to the USB cable). 2) ... Show Detail
- No：1654
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 14:03
- Category： Support tool
-
I use the Ethernet module (Type_NP1L-ET1). Is the IP address assigned automatically?
The IP address is not assigned automatically. (DHCP function is not supported.) The default IP address is '192.168.0.1'. You can check the IP address b... Show Detail
- No：1595
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
-
You can connect an SX series CPU to D300win via USB, Ethernet or a dedicated loader cable, depending on the model. Configure the communication settings acco... Show Detail
- No：1509
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:41
- Category： Support tool (D300win)
-
You don't need a dedicated cable. Since the parameters will be set via the CPU module, you need a loader cable for the PLC and the program loader software. Show Detail
- No：1676
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
Modules that use the processor bus, such as the P/PE link and FL-net modules, need be mounted on the slot equipped with the processor bus. Other communicati... Show Detail
- No：1673
- Displayed Date：2023/04/25 19:00
- Category： Others
-
When you use preset operation in the linear operation mode, counting is sometimes discontinued due to preset overflow. Show Detail
- No：1675
- Displayed Date：2023/04/25 19:00
- Category： Function
1-10 of Total 235