-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
- When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
- Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
- When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
- When I attempted to download a project to a CPU with user ROM card by using D300win, a message appeared saying 'Invalid loader command process!' an...
GLOBAL
Search by category
Keyword Search
FAQ within [ SPH ]
-
Please tell me how to register a T-link model of UG (or V Series) as a POD in the system definition.
Select a T-link capsule and set the numbers of input/output words. By default, a POD requires one word for input and one word for output. Show Detail
- No：1438
- Displayed Date：2023/04/25 19:00
- Category： Support tool
-
This only stops the operating CPU and the operation is not switched to the standby CPU. Show Detail
- No：1588
- Displayed Date：2023/04/25 19:00
- Category： Main unit
-
It occurs when any of the overrun, parity and framing errors is detected in the serial port of a general-purpose communication module. Show Detail
- No：1328
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
Is there an RAS that detects an error of the external power supply used for an I/O module?
No, there isn't. Receive the external power supply as an external input to detect the status. Show Detail
- No：1388
- Displayed Date：2023/04/25 19:00
- Category： Main unit
-
In exponentiation operation, when a negative value is used for the base, the result is 0. Show Detail
- No：1551
- Displayed Date：2023/04/25 19:00
- Category： Application
-
In MICREX-SX, a scan list is automatically created by registering the remote I/O to be connected to the master module in the system configuration definitions... Show Detail
- No：1346
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:35
- Category： Communication (Others)
-
Yes, it is the same. Show Detail
- No：1377
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
-
The memory usage is displayed in 'GM (global memory)' by the 'Device' function that is used to edit tags or check the memory usage. However, the memory cap... Show Detail
- No：1484
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
-
Pulse output completion is indicated by the 'Command pulse zero' signal. Normally, it is '1' to indicate the status of completion. When the number of pulses... Show Detail
- No：1548
- Displayed Date：2023/04/25 19:00
- Category： Function
-
A nonfatal fault of the takt cycle monitoring error has occurred. What is a possible cause?
The takt cycle monitoring error is caused by the following factors_ (1) The preset takt cycle value specified in the system definition is shorter than the ac... Show Detail
- No：1576
- Displayed Date：2023/04/25 19:00
- Category： Error
1-10 of Total 235