-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- I creat user FB in StandardV3, and defined input/output parameter as word (WV). Can I directly access any bit within this parameter WV?
- When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
- When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
- We share the D300win and other PLC engineering tool software among several people. Do we need to purchase the software for each person?
- Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
GLOBAL
Search by category
Keyword Search
FAQ within [ PLC ]
-
If the start bit remains on, the positioning end signal is not generated. Show Detail
- No：1317
- Displayed Date：2023/04/25 19:00
- Category： Function
-
In MICREX-SX, a scan list is automatically created by registering the remote I/O to be connected to the master module in the system configuration definitions... Show Detail
- No：1346
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:35
- Category： Communication (Others)
-
You cannot use D300win V2 for that. You can display them by using the grid-fixed type ladder editor of the D300win V3. Show Detail
- No：1440
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
-
To input the initial value, input '[value, value, ..., value].' In brackets, input values and use commas to separate values. Show Detail
- No：1299
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 14:19
- Category： Support tool (D300win)
-
A compilation error occurs if the properties of the POU do not match. Specify the CPU type as 'Common.' Show Detail
- No：1326
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:31
- Category： Support tool (D300win)
-
One possible cause is that common FB _C_COM is not registered with the library. For communication-related expansion FBs including _C_FREE, register common... Show Detail
- No：1329
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:32
- Category： Communication (Others)
-
Only open-collector (single-ended) signals are accepted. (NP1F-HC2 accepts differential signals.) The rated current is 40 mA and an encoder that permits t... Show Detail
- No：1373
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:43
- Category： Function
-
Input an arbitrary address. This setting is ignored for the unpassive mode. Show Detail
- No：1378
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
-
What is necessary for MODBUS_RTU communication between SPH and an external device?
The following are necessary. 1) Hardware: General-purpose communication module (NP1L-RS1/RS2/RS3/RS4/RS5) whose firmware version is V42 or later ... Show Detail
- No：1469
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:29
- Category： Communication (Others)
-
No, you cannot. Use the dedicated loader cable (Type_NW0H-CA3). Show Detail
- No：1511
- Displayed Date：2023/04/25 19:00
- Category： Support tool
1-10 of Total 398