The simulation function of the StandardV3 does not support the index register. Check the program operation using a har

It seems that this problem was caused by an improper address setting for INDAT/OUTDAT assigned to the counter FB termina

The SX control utility of the D300win V2 supports the P-link area monitoring function from V2.2.6.0 and later. Check the

For device display in StandardV3, a maximum of 2048 rows can be displayed on one window. To display WM2048 and the follo

For setting parameter values (such as P, I and D), it is possible to_ (1) Set the data within the user application (2)

No, it is not possible. Use an encoder of the line-driver or open-collector output type. When using a line-driver type,

The P-link memory is prepared in the P-link module. It is separate from the memory in the CPU and no change takes place

If the CPU modules are mounted on a hot plug base board with station No. setup function, you can replace them without tu

Note the following points (1) The rated output voltage is 12 to 24 V. Check the voltage of the device to be connected.

It is possible as long as the protocol is UDP/IP. In the M_OPEN FB, specify 255.255.255.255 as the IP address to be set

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC

Latest FAQ

I creat user FB in StandardV3, and defined input/output parameter as word (WV). Can I directly access any bit within this parameter WV?
When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
We share the D300win and other PLC engineering tool software among several people. Do we need to purchase the software for each person?
Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...

GLOBAL

Search by category

Keyword Search

FAQ within [ PLC ]

71-80 of Total 398

≪ 8 / 40page ≫

I converted an M/F program into an SX program with the Standard loader. I performed simulation of the converted program in the Standard loader, but...

The simulation function of the StandardV3 does not support the index register. Check the program operation using a hardware PLC. Show Detail
- No：1471
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
In the standard expansion counter FB _MHCNTH, CH0 operates but CH1 does not.

It seems that this problem was caused by an improper address setting for INDAT/OUTDAT assigned to the counter FB terminal. On a single module, assign the sa... Show Detail
- No：1539
- Displayed Date：2023/04/25 19:00
- Category： Function
I tried to see the P-link area by using the SX control utility of the D300win V2, but it was not displayed.

The SX control utility of the D300win V2 supports the P-link area monitoring function from V2.2.6.0 and later. Check the version. Note that all versions of... Show Detail
- No：1584
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
In the StandardV3, when I display devices for 'WM' by clicking [Device], WM0000 to WM2047 are displayed, however, WM2048 and the following addresse...

For device display in StandardV3, a maximum of 2048 rows can be displayed on one window. To display WM2048 and the following addresses, click the [Next page]... Show Detail
- No：1632
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
For PID control by using a PID FB package, how should I set the various parameters?

For setting parameter values (such as P, I and D), it is possible to_ (1) Set the data within the user application (2) Use 'PID FB parameter support ut... Show Detail
- No：1296
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 14:18
- Category： Function
Is it possible to use an encoder of the complementary output type for the high-speed counter module (Type_ NP1F-HC2)?

No, it is not possible. Use an encoder of the line-driver or open-collector output type. When using a line-driver type, pay attention to the output capacity ... Show Detail
- No：1320
- Displayed Date：2023/04/25 19:00
- Category： Function
In a redundant system, what will happen to the P-link memory at the time of switchover to a standby CPU?

The P-link memory is prepared in the P-link module. It is separate from the memory in the CPU and no change takes place at the time of switchover to a standb... Show Detail
- No：1343
- Displayed Date：2023/04/25 19:00
- Category： Main unit
When redundant CPUs mounted on the same base board break down, can I replace the CPU without turning off the power?

If the CPU modules are mounted on a hot plug base board with station No. setup function, you can replace them without turning off the power. Show Detail
- No：1367
- Displayed Date：2023/04/25 19:00
- Category： Main unit
I want to run an external device by pulse output with the high-speed output module (Type_ NP1Y32T09P1-A). What are the points to note regarding the...

Note the following points (1) The rated output voltage is 12 to 24 V. Check the voltage of the device to be connected. (2) The Z-phase/timing input signal f... Show Detail
- No：1399
- Displayed Date：2023/04/25 19:00
- Category： Function
Is broadcast communication via Ethernet possible?

It is possible as long as the protocol is UDP/IP. In the M_OPEN FB, specify 255.255.255.255 as the IP address to be set for the 'communication destination s... Show Detail
- No：1415
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)