It is possible with the Ethernet module software version V36 or later by using the F_READ (read)/F_WRITE (write) FB.

When the P-link module is specified as 'unimplemented' and no P-link module exists in the system, attempting to access t

The Web module requires Java software only for trend graph display. The cause is probably that the PC you are using does

Once a compilation error occurs during patch POU, the project must be compiled and downloaded again. Therefore, you need

There are two ways to connect a USB port of a personal computer and a CPU: 1) Connect to the USB port of the CPU (direc

It depends on the specifications and combinations of Ethernet devices. Communication ports of Ethernet devices have eit

During battery-less operation, previous fault information and other 'history of RAS' are not saved. Only the present RAS

The takt cycle monitoring error is caused by the following factors_ (1) The preset takt cycle value specified in the sys

Yes, you can connect MICREX-F series and SX series P-link modules, and communicate between them. * For the connection a

MICREX-SX series SPF is the replacement for FLEX-PC NB2 series. Refer to the following user's manual. 'Replacement Man

Search by category

Keyword Search

FAQ within [ PLC ]

61-70 of Total 398

≪ 7 / 40page ≫

Is it possible to read and write the IP address and port reference number of an Ethernet module (Type_ NP1L-ET1) by using a user application?

It is possible with the Ethernet module software version V36 or later by using the F_READ (read)/F_WRITE (write) FB. After writing, the power (or reset) o... Show Detail
- No：1370
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:42
- Category： Communication (Ethernet)
In an SPH system, I specified the P-link module as 'unimplemented' and the program execution time was extended. Why?

When the P-link module is specified as 'unimplemented' and no P-link module exists in the system, attempting to access the P-link memory using a contact, coi... Show Detail
- No：1355
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
I'm using the Web module (Type_ NP1L-WE1) and only the trend graph cannot be displayed properly on the PC. What is a possible cause?

The Web module requires Java software only for trend graph display. The cause is probably that the PC you are using does not have Java installed. Show Detail
- No：1308
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
When I change a program online (patch POU), error message shown 'The resevation area of the non-retain memory of POU xxx is short (2 word).' Why?

Once a compilation error occurs during patch POU, the project must be compiled and downloaded again. Therefore, you need to stop the CPU. Please consider the... Show Detail
- No：1661
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 14:05
- Category： Support tool (D300win)
I have connected the SX series CPU and the loader PC via USB. I have installed the USB driver and configured the communication settings, but commun...

There are two ways to connect a USB port of a personal computer and a CPU: 1) Connect to the USB port of the CPU (directly connected to the USB cable). 2) ... Show Detail
- No：1654
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 14:03
- Category： Support tool
For 1-to-1 communication of Ethernet, can I establish communication only using a LAN cable (cross cable), without using a hub?

It depends on the specifications and combinations of Ethernet devices. Communication ports of Ethernet devices have either of the following specifications. ... Show Detail
- No：1582
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:55
- Category： Communication (Ethernet)
When you use battery-less operation on the SPH, is the history of RAS information recorded?

During battery-less operation, previous fault information and other 'history of RAS' are not saved. Only the present RAS information is displayed. Show Detail
- No：1579
- Displayed Date：2023/04/25 19:00
- Category： Main unit
A nonfatal fault of the takt cycle monitoring error has occurred. What is a possible cause?

The takt cycle monitoring error is caused by the following factors_ (1) The preset takt cycle value specified in the system definition is shorter than the ac... Show Detail
- No：1576
- Displayed Date：2023/04/25 19:00
- Category： Error
Can I connect MICREX-F series and SX series P-link modules via P-link?

Yes, you can connect MICREX-F series and SX series P-link modules, and communicate between them. * For the connection and communication methods, see 'Sectio... Show Detail
- No：1460
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
What is the replacement for FLEX-PC NB2 series?

MICREX-SX series SPF is the replacement for FLEX-PC NB2 series. Refer to the following user's manual. 'Replacement Manual FLEX-PC NB2 to MICREX-SX SPF [Har... Show Detail
- No：1449
- Displayed Date：2023/04/25 19:00
- Category： Main unit