In a redundant system, both CPUs are identified as CPU0 and you cannot read a battery error of the standby CPU. Determin

Yes, it is the same as in the SPH series (except for SPH3000MM).

When the FALDIC-α se

Yes, there is a difference in system operation when control power supply for a servo amplifier is shut down. The ALPHA5

POU control data is different between the two data transfer methods: 1) by using the MOVE instruction and 2) by conne

You cannot upgrade 'MICREX-F PLC Programmer' free of change. 'MICREX-F PLC Programmer' that can be installed as NL4N-

An unused slot is permitted in a system configuration. If you plan to mount a module in the unused slot in the future

Data with an address with the smaller number is arranged on the lower-order side. For example, DM0 consists of two word

The received data is cleared to 0. Therefore, be sure not to read (ignore) the data by application program. Reopening th

For the Standard loader V2, you cannot specify array data for the operand that specifies the first address. (An error is

In Standard loader, to access the input memory from MONITOUCH, cancel the I/O group setting of the input specified as 'n

Search by category

Keyword Search

FAQ within [ PLC ]

41-50 of Total 398

≪ 5 / 40page ≫

An address error occurs when I read a battery error of the standby CPU (CPU1) from the operating CPU (CPU0).

In a redundant system, both CPUs are identified as CPU0 and you cannot read a battery error of the standby CPU. Determine the condition of the standby CPU fr... Show Detail
- No：1572
- Displayed Date：2023/04/25 19:00
- Category： Application
Is loader command communication using the SPF series Ethernet communication board (Type_NA3LA-ET1) or communication unit (Type_NA0LA-ET1) the same ...

Yes, it is the same as in the SPH series (except for SPH3000MM). Show Detail
- No：1515
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
When the FALDIC-α series is replaced with the ALPHA5 series or later, is there a difference in 'fail-soft operation' of each servo amplifier connec...

Yes, there is a difference in system operation when control power supply for a servo amplifier is shut down. The ALPHA5 series or later supports the MICREX-... Show Detail
- No：1503
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:39
- Category： Function
In D300win, there are two methods to transfer data, by using the MOVE instruction and by connecting variables with a line. Is there any difference ...

POU control data is different between the two data transfer methods: 1) by using the MOVE instruction and 2) by connecting variables with a line. Therefor... Show Detail
- No：1473
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
I am using the loader software 'MICREX-F PLC Programmer' (Type_NL4N-WNSB). Its version is old and does not support the latest Windows OS. Can I upg...

You cannot upgrade 'MICREX-F PLC Programmer' free of change. 'MICREX-F PLC Programmer' that can be installed as NL4N-WNSB is currently included with the p... Show Detail
- No：1455
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 09:36
- Category： Support tool (Others)
Is it permitted to have an unused slot in an SPH system configuration?

An unused slot is permitted in a system configuration. If you plan to mount a module in the unused slot in the future, it can be registered as 'unimplemen... Show Detail
- No：1313
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 14:32
- Category： Main unit
When a double-word address is used with the Standard Loader (Type_ NP4H-SWN), how are words arranged in terms of the higher and lower order?

Data with an address with the smaller number is arranged on the lower-order side. For example, DM0 consists of two words_ WM0 and WM1. WM0 is arranged on th... Show Detail
- No：1305
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...

The received data is cleared to 0. Therefore, be sure not to read (ignore) the data by application program. Reopening the FB (turning the 'OPEN' terminal fro... Show Detail
- No：1672
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
When I defined array (example WL990[WL0]) as start addoress of FMOVE in StandardV2 loader, error was detected by error check. Why?

For the Standard loader V2, you cannot specify array data for the operand that specifies the first address. (An error is detected during the program check.) ... Show Detail
- No：1665
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
To debug a PLC program without I/O module, I set I/Os as 'no equipment'. Then, I tried to set input contact (X) using switch of MONITOUCH. However,...

In Standard loader, to access the input memory from MONITOUCH, cancel the I/O group setting of the input specified as 'no equipment.' If the input specified... Show Detail
- No：1658
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 14:04
- Category： Support tool (Standard)

41-50 of Total 398

PLC

Common to N
- Support tool (Others)
Common to SX
- Support tool (D300win)
- |Application
- |Support tool
- |Support tool (Standard)
- |Others
- |Accessory
- |Error
- |Communication (T-link)
- |Function
- |Communication (Others)
- |Main unit
- |Communication (Ethernet)

SPB
SPF
- Others
- |Support tool
- |Communication (Ethernet)
- |Communication (Others)
- |Main unit
- |Application

SPH
- Communication (T-link)
- |Support tool (D300win)
- |Others
- |Communication (Others)
- |Main unit
- |Function
- |Communication (Ethernet)
- |Application
- |Accessory
- |Support tool (Standard)
- |I/O
- |Error
- |Support tool

Info & News

To Top of Page

PLC

Regional Websites

About Us

Products & Solutions

Investor Relations

Sustainability

Latest FAQ

GLOBAL

Search by category

Keyword Search

FAQ within [ PLC ]

PLC

Info & News