The near zero signal/command pulse zero signal/positioning end signal/RDY signal of the status information signals are s

Yes, it is possible. Note, however, that the values are of the INT data type.

One loop of control requires FB instances of about 300 words. Accordingly a CPU with FB instances for at least 18 K word

There is a high-capacity battery for SPH300 (Type_ NP8P-BTS). Its battery capacity (approximately 2700 mA) is about 2.7

It is possible with the Ethernet module software version V36 or later by using the F_READ (read)/F_WRITE (write) FB. Af

UI4 is not supported by the specification with the VB automation interface. Meanwhile, UI4 is supported by the custom in

Up to 4 units can be connected in 1 configuration (on 1 SX bus). Note, however, that they must be configured so that th

It is full duplex for both hardware and software (firmware) for anything other than communication by M_RECEIVE and M_SEN

Select a T-link capsule and set the numbers of input/output words. By default, a POD requires one word for input and on

To use a CF card as user ROM of the SPH Series, you need to format the CF card and initialize it (generate folders and f

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC

Latest FAQ

I creat user FB in StandardV3, and defined input/output parameter as word (WV). Can I directly access any bit within this parameter WV?
When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
We share the D300win and other PLC engineering tool software among several people. Do we need to purchase the software for each person?
Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...

GLOBAL

Search by category

Keyword Search

FAQ within [ PLC ]

31-40 of Total 398

≪ 4 / 40page ≫

With a positioning control module (Type_ NP1F-MP2/MA2), what are the statuses of the status information signals after power-up?

The near zero signal/command pulse zero signal/positioning end signal/RDY signal of the status information signals are set to [1]. The interrupt input sig... Show Detail
- No：1318
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:17
- Category： Function
Is it possible to use a variable for the initial value, end value and incremental value by using a 'FOR statement' of the ST language?

Yes, it is possible. Note, however, that the values are of the INT data type. Show Detail
- No：1337
- Displayed Date：2023/04/25 19:00
- Category： Application
I want to execute 60 loops of PID control. Which CPU should I choose? I use the SX-programmer Expert (D300win) as a loader.

One loop of control requires FB instances of about 300 words. Accordingly a CPU with FB instances for at least 18 K words is required. This leads to the conc... Show Detail
- No：1354
- Displayed Date：2023/04/25 19:00
- Category： Function
Is there a battery available with a longer backup time than the backup battery for SPH (Type_ NP8P-BT)?

There is a high-capacity battery for SPH300 (Type_ NP8P-BTS). Its battery capacity (approximately 2700 mA) is about 2.7 times that of the backup battery supp... Show Detail
- No：1360
- Displayed Date：2023/04/25 19:00
- Category： Accessory
Is it possible to read and write the IP address and port reference number of an Ethernet module (Type_ NP1L-ET1) by using a user application?

It is possible with the Ethernet module software version V36 or later by using the F_READ (read)/F_WRITE (write) FB. After writing, the power (or reset) o... Show Detail
- No：1370
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:42
- Category： Communication (Ethernet)
Is communication possible with the UI4 type not supported based on the manual description of the SX communication middleware (Type_ NP4N-MDLW)?

UI4 is not supported by the specification with the VB automation interface. Meanwhile, UI4 is supported by the custom interface specification. Show Detail
- No：1381
- Displayed Date：2023/04/25 19:00
- Category： Support tool
How many units of Ethernet module (Type_ NP1L-ET□) can be used in a system?

Up to 4 units can be connected in 1 configuration (on 1 SX bus). Note, however, that they must be configured so that the total number of units of other comm... Show Detail
- No：1395
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
With a general-purpose communication module, is RS232C completely full duplex?

It is full duplex for both hardware and software (firmware) for anything other than communication by M_RECEIVE and M_SEND on the SX bus, which are FB interna... Show Detail
- No：1413
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
Please tell me how to register a T-link model of UG (or V Series) as a POD in the system definition.

Select a T-link capsule and set the numbers of input/output words. By default, a POD requires one word for input and one word for output. Show Detail
- No：1438
- Displayed Date：2023/04/25 19:00
- Category： Support tool
What operation do I need to use a CF card as a user ROM card used for the CPU module of the SPH Series (SPH300 or SPH2000)?

To use a CF card as user ROM of the SPH Series, you need to format the CF card and initialize it (generate folders and files in the user ROM). The format sh... Show Detail
- No：1439
- Displayed Date：2023/04/25 19:00
- Category： Accessory