To make the 'Use USB port' check box selectable, the USB driver for MICREX-SX must be installed on the PC in use. Insta

The flashing of the LED of the high-speed output module (Type_ NP1Y32T09P1-A) indicates that pulse output is generated.

The standard MICREX-SX SPH models have been designed for use in tropical wetlands. Therefore, all you need to do is to

Check to make sure that_ (1) The channel specification (CH_SEL) is correct. (2) The FB instance names are not duplicated

It is not provided as internal memory. You need to create the circuit shown in the attached diagram. The example shows a

Check the following two points (1) To use the EMG/±OT signal, input the 'External power supply 24 V DC.' (2) Check the

If the CPU supports user ROM (CF or SD card), you can do it by sending the program data for operation to the site by e-m

It depends on the specifications and combinations of Ethernet devices. Communication ports of Ethernet devices have eith

Unless you register the module in the system definition and set the I/O group in the CPU parameters, data monitoring is

This was probably caused by one of the following two factors_ (1) ±OT is set to 'Disabled' in the parameter setting of

Search by category

Keyword Search

FAQ within [ PLC ]

321-330 of Total 398

≪ 33 / 40page ≫

Of the communication port settings (MICREX-SX) of the Standard Loader (Type_ NP4H-SWN), the 'Use USB port' check box cannot be selected.

To make the 'Use USB port' check box selectable, the USB driver for MICREX-SX must be installed on the PC in use. Install the USB driver (dedicated) conta... Show Detail
- No：1306
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 14:31
- Category： Support tool (Standard)
With the high-speed output module (Type_ NP1Y32T09P1-A), the LED flashes but no pulse is output to the outside. What should I check?

The flashing of the LED of the high-speed output module (Type_ NP1Y32T09P1-A) indicates that pulse output is generated. If no pulse output is generated in t... Show Detail
- No：1291
- Displayed Date：2023/04/25 19:00
- Category： Function
I want MICREX-SX SPH models adapted to tropical wetlands.

The standard MICREX-SX SPH models have been designed for use in tropical wetlands. Therefore, all you need to do is to order standard models. Show Detail
- No：1287
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 14:17
- Category： Others
With a counter module (NP1F-HC2), I use ２ counter FBs to control 2 channels. At system start-up, I set simultaneous preset operations for the 2 cha...

Check to make sure that_ (1) The channel specification (CH_SEL) is correct. (2) The FB instance names are not duplicated. (3) The preset command is given aft... Show Detail
- No：1640
- Displayed Date：2023/04/25 19:00
- Category： Function
I create a program for the SPH by using the Standard Loader (Type_ NP4H-SWN). Is flicker relay memory available?

It is not provided as internal memory. You need to create the circuit shown in the attached diagram. The example shows a circuit in which M0 repeats ON and O... Show Detail
- No：1605
- Displayed Date：2023/04/25 19:00
- Category： Application
When I turned on the positioning control module (Type_ NP1F-MP2/MA2), the EMG/±OT LED lights up and positioning operation is disabled. What causes ...

Check the following two points (1) To use the EMG/±OT signal, input the 'External power supply 24 V DC.' (2) Check the wiring of the external equipment. (T... Show Detail
- No：1601
- Displayed Date：2023/04/25 19:00
- Category： Function
There is no loader at the site. Is there any way to change the program?

If the CPU supports user ROM (CF or SD card), you can do it by sending the program data for operation to the site by e-mail or another method and then transf... Show Detail
- No：1592
- Displayed Date：2023/04/25 19:00
- Category： Main unit
For 1-to-1 communication of Ethernet, can I establish communication only using a LAN cable (cross cable), without using a hub?

It depends on the specifications and combinations of Ethernet devices. Communication ports of Ethernet devices have either of the following specifications. ... Show Detail
- No：1582
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:55
- Category： Communication (Ethernet)
Does data monitoring of the I/O area require the module to be registered in the system definition?

Unless you register the module in the system definition and set the I/O group in the CPU parameters, data monitoring is disabled because no memory is reserve... Show Detail
- No：1581
- Displayed Date：2023/04/25 19:00
- Category： Support tool
Although the LED for ±OT lights up on the positioning control module (Type_ NP1F-MP2/MA2), the positioning operation finishes. What is the causal f...

This was probably caused by one of the following two factors_ (1) ±OT is set to 'Disabled' in the parameter setting of the positioning control module (Type_... Show Detail
- No：1575
- Displayed Date：2023/04/25 19:00
- Category： Function