The module is equipped with 2 channels of high-speed counter and signals of a different voltage can be counted for each

There is a limit to the number of POUs that can be opened simultaneously_ 31 including 'Data 1,' 'Simulation' and 'AFB.'

The set value of the timer must be a 32-bit (double-word) value. Specify DM (double-word), not WM (single-word). The mem

There is a high-capacity battery for SPH300 (Type_ NP8P-BTS). Its battery capacity (approximately 2700 mA) is about 2.7

One likely cause is that any of the following characters is used in the variable worksheet (1) A double-byte space is u

Both the pulse output and control output are open collector outputs. They should be used within the following ranges (1)

As an alternative, you can combine hardware and software functions. (1) Hardware_ Prepare a relay output card and use

In a redundant system, both CPUs are identified as CPU0 and you cannot read a battery error of the standby CPU. Determin

Yes, you can use NP1L-RS1/RS4/RS5 for RS-422 devices. RS-485 is upper compatible with RS-422. There are two connection t

The simulation function of the StandardV3 does not support the index register. Check the program operation using a har

Search by category

Keyword Search

FAQ within [ PLC ]

231-240 of Total 398

≪ 24 / 40page ≫

I understand that the high-speed counter module (Type_ NP1F-HC2MR) is capable of counting pulses of 5 V/12 V/24 V. Is it possible to count with a d...

The module is equipped with 2 channels of high-speed counter and signals of a different voltage can be counted for each channel. To set the signal level, s... Show Detail
- No：1398
- Displayed Date：2023/04/25 19:00
- Category： Function
When I use the Standard Loader (Type_ NP4H-SWN) to add 35 POUs under a program configuration and attempt to open the POUs, I can open up to the 28t...

There is a limit to the number of POUs that can be opened simultaneously_ 31 including 'Data 1,' 'Simulation' and 'AFB.' Show Detail
- No：1362
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
When I used the Standard Loader (Type_ NP4H-SWN) to input a timer instruction and specified the WM area for indirectly specifying the timer set val...

The set value of the timer must be a 32-bit (double-word) value. Specify DM (double-word), not WM (single-word). The memory to use may be DX or DL, as well a... Show Detail
- No：1361
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
Is there a battery available with a longer backup time than the backup battery for SPH (Type_ NP8P-BT)?

There is a high-capacity battery for SPH300 (Type_ NP8P-BTS). Its battery capacity (approximately 2700 mA) is about 2.7 times that of the backup battery supp... Show Detail
- No：1360
- Displayed Date：2023/04/25 19:00
- Category： Accessory
With D300win V2, I created global variables first and edited a ladder but some variables do not appear on the pull-down list for variable name inpu...

One likely cause is that any of the following characters is used in the variable worksheet (1) A double-byte space is used. Use a single-byte space or tab... Show Detail
- No：1356
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:38
- Category： Support tool (D300win)
I use the pulse train output positioning control module (Type_ NP1F-HP2). Please tell me the rated voltage/current of the pulse output and control ...

Both the pulse output and control output are open collector outputs. They should be used within the following ranges (1) Pulse output_ 30 V DC, 40 mA or less... Show Detail
- No：1602
- Displayed Date：2023/04/25 19:00
- Category： Function
The SPH does not have a RUN contact. Is there any alternative?

As an alternative, you can combine hardware and software functions. (1) Hardware_ Prepare a relay output card and use one point as a RUN contact. 　(2) Sof... Show Detail
- No：1587
- Displayed Date：2023/04/25 19:00
- Category： Main unit
An address error occurs when I read a battery error of the standby CPU (CPU1) from the operating CPU (CPU0).

In a redundant system, both CPUs are identified as CPU0 and you cannot read a battery error of the standby CPU. Determine the condition of the standby CPU fr... Show Detail
- No：1572
- Displayed Date：2023/04/25 19:00
- Category： Application
NP1L-RS1/RS4/RS5 support RS-485. Can I use them for RS-422 devices?

Yes, you can use NP1L-RS1/RS4/RS5 for RS-422 devices. RS-485 is upper compatible with RS-422. There are two connection types for RS-422 devices: 2-wire conne... Show Detail
- No：1522
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
I converted an M/F program into an SX program with the Standard loader. I performed simulation of the converted program in the Standard loader, but...

The simulation function of the StandardV3 does not support the index register. Check the program operation using a hardware PLC. Show Detail
- No：1471
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)

231-240 of Total 398

PLC

Common to N
- Support tool (Others)
Common to SX
- Support tool (D300win)
- |Application
- |Support tool
- |Support tool (Standard)
- |Others
- |Accessory
- |Error
- |Communication (T-link)
- |Function
- |Communication (Others)
- |Main unit
- |Communication (Ethernet)

SPB
SPF
- Others
- |Support tool
- |Communication (Ethernet)
- |Communication (Others)
- |Main unit
- |Application

SPH
- Communication (T-link)
- |Support tool (D300win)
- |Others
- |Communication (Others)
- |Main unit
- |Function
- |Communication (Ethernet)
- |Application
- |Accessory
- |Support tool (Standard)
- |I/O
- |Error
- |Support tool

Info & News

To Top of Page

PLC

Regional Websites

About Us

Products & Solutions

Investor Relations

Sustainability

Latest FAQ

GLOBAL

Search by category

Keyword Search

FAQ within [ PLC ]

PLC

Info & News