1) By the mechanism of program conversion, unused FBs are also registered. However, FBs not used in the program ar

Timers of small numbers (T0 to T8191) are local timers (timers effective within the program only). To create timers tha

The range in terms of description is up to 4096 words respectively. Note, however, that actual message transfer on the S

The program memory, data memory and system definitions in the CPU can be saved to a PC as a data file by using the 'Back

Clock adjustment is initiated from CPU0 (operating) to other CPUs (standby). It takes place on a constant (1-minute) cyc

(1) For Expert (D300win) No master control instruction is provided. This is because the MICREX-SX Series is dedicat

The current value of the timer can be changed. Note, however, that a circuit for changing the current value of the time

Use the recommended shielded twisted pair cable mentioned in the User's Manual. Also provide shielding.

The set value of the timer must be a 32-bit (double-word) value. Specify DM (double-word), not WM (single-word). The mem

A possible cause is that a “Deviation amount over error” occurred. For details, refer to the user's manual FEH213 (NP1F-

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC

Latest FAQ

I creat user FB in StandardV3, and defined input/output parameter as word (WV). Can I directly access any bit within this parameter WV?
When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
We share the D300win and other PLC engineering tool software among several people. Do we need to purchase the software for each person?
Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...

GLOBAL

Search by category

Keyword Search

FAQ within [ PLC ]

181-190 of Total 398

≪ 19 / 40page ≫

1) When converting a program on Standard, about 100 FBs are registered in 'Function Blocks.' Are they all FBs being used? 2) Can I find out where a...

1) By the mechanism of program conversion, unused FBs are also registered. However, FBs not used in the program are not downloaded to the CPU, therefor... Show Detail
- No：1508
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
When I was creating a program for the SPH Series with the Standard Loader (Type_ NP4H-SWN) and divided the program, the timer entered an error status.

Timers of small numbers (T0 to T8191) are local timers (timers effective within the program only). To create timers that are effective in other programs (g... Show Detail
- No：1437
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
What is the transfer data size range for the READ_WORD/WRITE_WORD FB?

The range in terms of description is up to 4096 words respectively. Note, however, that actual message transfer on the SX bus takes place after division into... Show Detail
- No：1410
- Displayed Date：2023/04/25 19:00
- Category： Application
I am going to replace the CPU. Is there any way to save the current data retained at one time and apply them to the new CPU?

The program memory, data memory and system definitions in the CPU can be saved to a PC as a data file by using the 'Backup' function included in the 'SX cont... Show Detail
- No：1402
- Displayed Date：2023/04/25 19:00
- Category： Support tool
Does equalization (from an operating CPU to a standby CPU) of the internal clock take place automatically? If so, when does it take place?

Clock adjustment is initiated from CPU0 (operating) to other CPUs (standby). It takes place on a constant (1-minute) cycle at the time of and after system st... Show Detail
- No：1401
- Displayed Date：2023/04/25 19:00
- Category： Main unit
Can a master control instruction be used in the MICREX-SX Series?

(1) For Expert (D300win) No master control instruction is provided. This is because the MICREX-SX Series is dedicated to programmable logic controlle... Show Detail
- No：1389
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:17
- Category： Application
With a project created by using D300win, is it possible to change the current value of the timer? If so, how can I change the value?

The current value of the timer can be changed. Note, however, that a circuit for changing the current value of the timer must be added. Show Detail
- No：1375
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:44
- Category： Support tool (D300win)
What measures can I take against external noise of the high-speed counter (Type_ NP1F-HC2)?

Use the recommended shielded twisted pair cable mentioned in the User's Manual. Also provide shielding. Show Detail
- No：1365
- Displayed Date：2023/04/25 19:00
- Category： Function
When I used the Standard Loader (Type_ NP4H-SWN) to input a timer instruction and specified the WM area for indirectly specifying the timer set val...

The set value of the timer must be a 32-bit (double-word) value. Specify DM (double-word), not WM (single-word). The memory to use may be DX or DL, as well a... Show Detail
- No：1361
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
On the positioning module (Type_NP1F-MP2/MA2), the 'ERR' LED turns ON. What are the possible causes?

A possible cause is that a “Deviation amount over error” occurred. For details, refer to the user's manual FEH213 (NP1F-MA2) or FEH214 (NP1F-MP2) 'Section 8 ... Show Detail
- No：1290
- Displayed Date：2023/04/25 19:00
- Category： Function