When the initial value of REAL type is '5.0,' for example, processing it through Excel changes it to '5' of the INT type

When the site environment is unfavorable, you are recommended to use the dedicated loader cable. Version V3.2.0.0 or la

The communication specification of the remote master does not control remote devices by the station No. Therefore, you c

By changing the zoom rate of the main screen displaying a program or data monitoring, the on-screen font size is also i

Yes, it is the same as in the SPH series (except for SPH3000MM).

If this is caused by a fluctuation in the input temperature, moving average processing shown below may improve the condi

The measurement accuracy does not include zero junction compensation accuracy. The zero junction compensation accuracy

Yes, you can. Note, however, that the input impedance reduces to half. Pay attention to the drive ability of the sensor.

Yes, it is possible. Of the parameter setting items of initialization, changes made to specific parameter items (such as

Since the slave is connected to T-link, it is handled as a 'T-link capsule.' Select the T-link capsule and set the numb

Search by category

Keyword Search

FAQ within [ PLC ]

171-180 of Total 398

≪ 18 / 40page ≫

When I output a variable worksheet of D300win to Excel, modify only comments on Excel and send it back to D300win, a compilation error is generated...

When the initial value of REAL type is '5.0,' for example, processing it through Excel changes it to '5' of the INT type and that causes a data type mismatch... Show Detail
- No：1422
- Displayed Date：2023/04/25 19:00
- Category： Error
I connect D300win by USB for communication but it is sometimes interrupted perhaps because the site environment is unfavorable. Is there any way to...

When the site environment is unfavorable, you are recommended to use the dedicated loader cable. Version V3.2.0.0 or later or V2.2.6.0 or later of D300win ... Show Detail
- No：1423
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
When a remote terminal master (NP1L-RM1) has been registered in 1-to-N or N-to-N mode in the system definition, can I register a remote device as '...

The communication specification of the remote master does not control remote devices by the station No. Therefore, you cannot register remote devices as 'No ... Show Detail
- No：1486
- Displayed Date：2023/04/25 19:00
- Category： Support tool
Can I increase the font size displayed on the Standard loader screen?

By changing the zoom rate of the main screen displaying a program or data monitoring, the on-screen font size is also increased or decreased. However, the S... Show Detail
- No：1501
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
Is loader command communication using the SPF series Ethernet communication board (Type_NA3LA-ET1) or communication unit (Type_NA0LA-ET1) the same ...

Yes, it is the same as in the SPH series (except for SPH3000MM). Show Detail
- No：1515
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
The temperature measurement value of the resistance temperature sensor (PT input) is unstable.

If this is caused by a fluctuation in the input temperature, moving average processing shown below may improve the condition. 1) Change the digital filter v... Show Detail
- No：1586
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:56
- Category： I/O
Does the accuracy specification of the thermocouple input module (Type_ NP1AXH4-TC) include zero junction compensation accuracy?

The measurement accuracy does not include zero junction compensation accuracy. The zero junction compensation accuracy is ±1°C (at ambient temperature 0°C ... Show Detail
- No：1597
- Displayed Date：2023/04/25 19:00
- Category： I/O
I will use the analog voltage input module. Can I input a single input signal to two CHs of the module simultaneously (in parallel) to use them?

Yes, you can. Note, however, that the input impedance reduces to half. Pay attention to the drive ability of the sensor. Show Detail
- No：1622
- Displayed Date：2023/04/25 19:00
- Category： I/O
In the communication module (NP1L-RS1/RS2/RS3/RS4/RS5), is it possible to change communication parameter such as fixed length to variable length af...

Yes, it is possible. Of the parameter setting items of initialization, changes made to specific parameter items (such as frame detection, code conversion and... Show Detail
- No：1639
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
I want to register a T-link slave (NP1L-TS1) under T-link master (NP1L-TL1), but the T-link slave is not shown in the list of system definition. Ho...

Since the slave is connected to T-link, it is handled as a 'T-link capsule.' Select the T-link capsule and set the numbers of input/output words in the par... Show Detail
- No：1642
- Displayed Date：2023/04/25 19:00
- Category： Communication (T-link)

171-180 of Total 398

PLC

Common to N
- Support tool (Others)
Common to SX
- Support tool (D300win)
- |Application
- |Support tool
- |Support tool (Standard)
- |Others
- |Accessory
- |Error
- |Communication (T-link)
- |Function
- |Communication (Others)
- |Main unit
- |Communication (Ethernet)

SPB
SPF
- Others
- |Support tool
- |Communication (Ethernet)
- |Communication (Others)
- |Main unit
- |Application

SPH
- Communication (T-link)
- |Support tool (D300win)
- |Others
- |Communication (Others)
- |Main unit
- |Function
- |Communication (Ethernet)
- |Application
- |Accessory
- |Support tool (Standard)
- |I/O
- |Error
- |Support tool

Info & News

To Top of Page

PLC

Regional Websites

About Us

Products & Solutions

Investor Relations

Sustainability

Latest FAQ

GLOBAL

Search by category

Keyword Search

FAQ within [ PLC ]

PLC

Info & News