Selecting the DCE mode for the communication parameter_ DCE designation keeps DSR always on.

One M_OPEN consumes one port of SPORT_NO, which is the local port. RPORT_NO is the port of the other end of the communi

Since the slave is connected to T-link, it is handled as a 'T-link capsule.' Select the T-link capsule and set the numb

In the MV selection part in the PID FB, (1) the backward operation uses the internally calculated MV value (%) without p

When the memory with a retain attribute is corrupted, the CPU clears the memory and operates in nonfatal fault condition

In a redundant system, both CPUs are identified as CPU0 and you cannot read a battery error of the standby CPU. Determin

Set the I/O area of the positioning module following the steps below. 1) Set 'h1C00' in the offset word address +16 (Ch1

Refer to the following How-to Guide, which describes how to update a program while a redundant system is running. MICRE

The flashing of the LED of the high-speed output module (Type_ NP1Y32T09P1-A) indicates that pulse output is generated.

The backup battery is intended to back up the data memory (SRAM) inside of the CPU. While the system is turned on, the p

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC

Latest FAQ

I creat user FB in StandardV3, and defined input/output parameter as word (WV). Can I directly access any bit within this parameter WV?
When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
We share the D300win and other PLC engineering tool software among several people. Do we need to purchase the software for each person?
Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...

GLOBAL

Search by category

Keyword Search

FAQ within [ PLC ]

101-110 of Total 398

≪ 11 / 40page ≫

When does the port status_ DSR (data set ready) in a structure variable_ RAS of the non-procedural standard expansion FB for communication remain on?

Selecting the DCE mode for the communication parameter_ DCE designation keeps DSR always on. Show Detail
- No：1297
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
I use the Ethernet module (NP1L-ET1/ET2) and using communication FB (M_OPEN). M_OPEN sets two ports of RPORT_NO and SPORT_NO. Does this mean that o...

One M_OPEN consumes one port of SPORT_NO, which is the local port. RPORT_NO is the port of the other end of the communication seen from the SX. Show Detail
- No：1643
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
I want to register a T-link slave (NP1L-TS1) under T-link master (NP1L-TL1), but the T-link slave is not shown in the list of system definition. Ho...

Since the slave is connected to T-link, it is handled as a 'T-link capsule.' Select the T-link capsule and set the numbers of input/output words in the par... Show Detail
- No：1642
- Displayed Date：2023/04/25 19:00
- Category： Communication (T-link)
What is the difference between the PID forward and backward operations when the PID FB package is used?

In the MV selection part in the PID FB, (1) the backward operation uses the internally calculated MV value (%) without processing it (as-is)_ and (2) the for... Show Detail
- No：1625
- Displayed Date：2023/04/25 19:00
- Category： Function
When the retain memory (memory for data backup with a battery) of the CPU module of the MICREX-SX Series SPH is corrupted, how does the CPU module ...

When the memory with a retain attribute is corrupted, the CPU clears the memory and operates in nonfatal fault condition. If the power is reset again in this... Show Detail
- No：1611
- Displayed Date：2023/04/25 19:00
- Category： Main unit
An address error occurs when I read a battery error of the standby CPU (CPU1) from the operating CPU (CPU0).

In a redundant system, both CPUs are identified as CPU0 and you cannot read a battery error of the standby CPU. Determine the condition of the standby CPU fr... Show Detail
- No：1572
- Displayed Date：2023/04/25 19:00
- Category： Application
How do I use a manual pulse generator with the positioning module (Type_NP1F-MP2/MA2)?

Set the I/O area of the positioning module following the steps below. 1) Set 'h1C00' in the offset word address +16 (Ch1 Set value area: Low word). (Set ... Show Detail
- No：1396
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:17
- Category： Function
In a CPU redundant system, how can I update a program while the system is running?

Refer to the following How-to Guide, which describes how to update a program while a redundant system is running. MICREX SX How-to Guide 'How to Change Prog... Show Detail
- No：1352
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
With the high-speed output module (Type_ NP1Y32T09P1-A), the LED flashes but no pulse is output to the outside. What should I check?

The flashing of the LED of the high-speed output module (Type_ NP1Y32T09P1-A) indicates that pulse output is generated. If no pulse output is generated in t... Show Detail
- No：1291
- Displayed Date：2023/04/25 19:00
- Category： Function
Is the backup battery consumed while the control power supply of the CPU is active?

The backup battery is intended to back up the data memory (SRAM) inside of the CPU. While the system is turned on, the power is supplied from the control pow... Show Detail
- No：1621
- Displayed Date：2023/04/25 19:00
- Category： Accessory