Note the following points (1) The rated output voltage is 12 to 24 V. Check the voltage of the device to be connected.

The Web module requires Java software only for trend graph display. The cause is probably that the PC you are using does

As an alternative, you can combine hardware and software functions. (1) Hardware_ Prepare a relay output card and use

Since the parameter data area of the positioning control module (Type_ NP1F-MP2/MA2) operates on the RAM, it is always c

A normal timer instruction specifies the effective timer range in the unit used on the POU. Since the timer numbers (T0

RS-485 is upper compatible with RS-422. In general, RS-422 devices mainly use 4-wire connection method, while RS-485 dev

The supported Windows OSes depend on the loader version. ? Windows 7: V3.5.3.18 or later ? Windows 8: V3.6.5.19 o

No, you cannot upload a definition file. So, it is very important to keep backup of Definition file on PC side.

When the EMG signal and ±OT signal are not used, connect them to 24 V DC. Alternatively, you can set the ±OT signal to

The current value of the timer can be changed. Note, however, that a circuit for changing the current value of the ti

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC

Latest FAQ

I creat user FB in StandardV3, and defined input/output parameter as word (WV). Can I directly access any bit within this parameter WV?
When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
We share the D300win and other PLC engineering tool software among several people. Do we need to purchase the software for each person?
Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...

GLOBAL

Search by category

Keyword Search

FAQ within [ PLC ]

71-80 of Total 398

≪ 8 / 40page ≫

I want to run an external device by pulse output with the high-speed output module (Type_ NP1Y32T09P1-A). What are the points to note regarding the...

Note the following points (1) The rated output voltage is 12 to 24 V. Check the voltage of the device to be connected. (2) The Z-phase/timing input signal f... Show Detail
- No：1399
- Displayed Date：2023/04/25 19:00
- Category： Function
I'm using the Web module (Type_ NP1L-WE1) and only the trend graph cannot be displayed properly on the PC. What is a possible cause?

The Web module requires Java software only for trend graph display. The cause is probably that the PC you are using does not have Java installed. Show Detail
- No：1308
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
The SPH does not have a RUN contact. Is there any alternative?

As an alternative, you can combine hardware and software functions. (1) Hardware_ Prepare a relay output card and use one point as a RUN contact. 　(2) Sof... Show Detail
- No：1587
- Displayed Date：2023/04/25 19:00
- Category： Main unit
When I turned on the positioning control module (Type_ NP1F-MP2/MA2) in the morning, the parameters were reset to the initial values. What is the f...

Since the parameter data area of the positioning control module (Type_ NP1F-MP2/MA2) operates on the RAM, it is always cleared when you turn off the module. ... Show Detail
- No：1573
- Displayed Date：2023/04/25 19:00
- Category： Function
With the Standard Loader (Type_ NP4H-SWN), I cannot use a timer (T0) created on a different POU at a contact.

A normal timer instruction specifies the effective timer range in the unit used on the POU. Since the timer numbers (T0 to T8191) are treated as a local devi... Show Detail
- No：1544
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
What is the difference between RS-485 and RS-422 ?

RS-485 is upper compatible with RS-422. In general, RS-422 devices mainly use 4-wire connection method, while RS-485 devices mainly use 2-wire connection met... Show Detail
- No：1521
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
What Windows OS does the Expert (D300win) support?

The supported Windows OSes depend on the loader version. ? Windows 7: V3.5.3.18 or later ? Windows 8: V3.6.5.19 or later ? Windows 8.1 and 10: V3.6.... Show Detail
- No：1492
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
Can I upload a definition file downloaded from a configurator to NP1L-PD1/PD2?

No, you cannot upload a definition file. So, it is very important to keep backup of Definition file on PC side. Show Detail
- No：1468
- Displayed Date：2023/04/25 19:00
- Category： Support tool
Please tell me the wiring method for the positioning control module (Type_ NP1F-MP2/MA2) when the EMG signal and ±OT signal are not used.

When the EMG signal and ±OT signal are not used, connect them to 24 V DC. Alternatively, you can set the ±OT signal to 'Disabled' in the parameter settings ... Show Detail
- No：1432
- Displayed Date：2023/04/25 19:00
- Category： Function
With a project created by using D300win, is it possible to change the current value of the timer? If so, how can I change the value?

The current value of the timer can be changed. Note, however, that a circuit for changing the current value of the timer must be added. Show Detail
- No：1375
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:44
- Category： Support tool (D300win)