POU control data is different between the two data transfer methods: 1) by using the MOVE instruction and 2) by conne

Once a compilation error occurs during patch POU, the project must be compiled and downloaded again. Therefore, you need

This error occurs when the system configuration set by the loader software differs from the actual configuration. For e

The supported Windows OS depends on the loader version. Windows 7: V1.3.3.2 or later, Windows 8: V1.3.4.1 or late

No, you cannot use NW0H-CNV. The RS-232C/422 converter for personal computer loaders (Type_NW0H-CNV) needs to be supplie

Select 'PS32/PS74/PS117/PS245.' With the D300win, 'NP1PS-32/74/117' and 'NP1PS-32R/74R/117R' indicate the same model s

Use the following communication cables from Furukawa Electric Co., Ltd. ・KPEV-SB 0.75mm2 x 1 pair (Max. length: 700m)

When you set a password for Level 3 access control, you cannot change settings from the loader or clear the memory unles

No, they do not need to be consecutive. If there are a lot of unused addresses, it may be better to assign addresses

Search by category

Keyword Search

FAQ within [ PLC ]

41-50 of Total 398

≪ 5 / 40page ≫

In D300win, there are two methods to transfer data, by using the MOVE instruction and by connecting variables with a line. Is there any difference ...

POU control data is different between the two data transfer methods: 1) by using the MOVE instruction and 2) by connecting variables with a line. Therefor... Show Detail
- No：1473
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
When I change a program online (patch POU), error message shown 'The resevation area of the non-retain memory of POU xxx is short (2 word).' Why?

Once a compilation error occurs during patch POU, the project must be compiled and downloaded again. Therefore, you need to stop the CPU. Please consider the... Show Detail
- No：1661
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 14:05
- Category： Support tool (D300win)
When I started a MICREX-SX series PLC after downloading a program into it, a fatal fault occurred. The loader software says 'system construction er...

This error occurs when the system configuration set by the loader software differs from the actual configuration. For example, a defined module is not mount... Show Detail
- No：1649
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 14:07
- Category： Support tool
Which OS does MICREX-F PLC Programmer support?

The supported Windows OS depends on the loader version. Windows 7: V1.3.3.2 or later, Windows 8: V1.3.4.1 or later, Windows 8.1 and 10: V1.3.5.0 or... Show Detail
- No：1454
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Others)
The loader connector of SPH series CPU modules has been changed into RJ45 connector. Can I use an RS-232C/422 converter for personal computer loade...

No, you cannot use NW0H-CNV. The RS-232C/422 converter for personal computer loaders (Type_NW0H-CNV) needs to be supplied power from the PLC side, however, t... Show Detail
- No：1529
- Displayed Date：2023/04/25 19:00
- Category： Support tool
I use the CPU module of Type NP1PS-32R/74R/117R/245R. When I create a new project, the displayed option is 'PS32/PS74/PS117/PS245' only. Which shou...

Select 'PS32/PS74/PS117/PS245.' With the D300win, 'NP1PS-32/74/117' and 'NP1PS-32R/74R/117R' indicate the same model selection. This applies to all CPUs ... Show Detail
- No：1666
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
Does the USB driver for SPF that is used to connect a personal computer loader support Windows 10?

Yes, it supports Windows 10. Show Detail
- No：1488
- Displayed Date：2023/04/25 19:00
- Category： Support tool
What cable should I use for T-link?

Use the following communication cables from Furukawa Electric Co., Ltd. ・KPEV-SB 0.75mm2 x 1 pair (Max. length: 700m) ・T-KPEV-SB 1.25mm2 x 1 pair (Max. le... Show Detail
- No：1278
- Displayed Date：2023/04/25 19:00
- Category： Communication (T-link)
With the MICREX-SX, I set a password for Level 3 access control on the CPU but I forgot the password. I do not mind about losing the program. Is it...

When you set a password for Level 3 access control, you cannot change settings from the loader or clear the memory unless you enter the password for authenti... Show Detail
- No：1561
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:52
- Category： Support tool
Do addresses of T-link devices (slave stations) connected to T-link need to be consecutive?

No, they do not need to be consecutive. If there are a lot of unused addresses, it may be better to assign addresses at some intervals for the future expa... Show Detail
- No：1276
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 14:14
- Category： Communication (T-link)