-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- I creat user FB in StandardV3, and defined input/output parameter as word (WV). Can I directly access any bit within this parameter WV?
- When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
- When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
- We share the D300win and other PLC engineering tool software among several people. Do we need to purchase the software for each person?
- Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
GLOBAL
Search by category
Keyword Search
FAQ within [ PLC ]
-
How can I hide ENO/EN of functions in D300win?
In the [Extras] menu, click [Options] to display the 'Options' dialog box. On the [Graphical editor] tab window, uncheck 'Functions with EN/ENO' option. This... Show Detail
- No：1403
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
-
They are assigned from words with the lowest numbers in a left-justified manner. Show Detail
- No：1385
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
-
What measures can I take against external noise of the high-speed counter (Type_ NP1F-HC2)?
Use the recommended shielded twisted pair cable mentioned in the User's Manual. Also provide shielding. Show Detail
- No：1365
- Displayed Date：2023/04/25 19:00
- Category： Function
-
Is there an alarm output contact to use when an error occurs in the PLC system?
For an alarm contact output of an error of the PLC system, select an arbitrary output module in the system definitions and define its 0th bit as a 'system DO... Show Detail
- No：1347
- Displayed Date：2023/04/25 19:00
- Category： Main unit
-
On the positioning module (Type_NP1F-MP2/MA2), the 'ERR' LED turns ON. What are the possible causes?
A possible cause is that a “Deviation amount over error” occurred. For details, refer to the user's manual FEH213 (NP1F-MA2) or FEH214 (NP1F-MP2) 'Section 8 ... Show Detail
- No：1290
- Displayed Date：2023/04/25 19:00
- Category： Function
-
Use the 'Excitation timing output' signal for the Z-phase pulse when a stepping motor is used. Show Detail
- No：1574
- Displayed Date：2023/04/25 19:00
- Category： Function
-
Usually, set the CPU No. to 0. The CPU No. 0 works as a master of an SX bus system. In a multi-CPU system or a CPU redundant system which uses multiple CPU ... Show Detail
- No：1504
- Displayed Date：2023/04/25 19:00
- Category： Main unit
-
The D300win cannot connect to the SX via the Ethernet module.
The IP address of the Ethernet module will become effective when the power supply is turned off once and then turned on again after the module driver is dow... Show Detail
- No：1434
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
391-398 of Total 398