Yes, they are. The maximum size is 32 words including the actual data, start code, end code, and BCC. (The same applies

This was probably caused by the following factors (1) The PC was not restarted after the D300win was installed. (2) A

Up to 4 units can be connected in 1 configuration (on 1 SX bus). Note, however, that they must be configured so that th

For an analog input range (1 to 5 V or 4 to 20 mA), a line breakage detection function is provided. An input voltage of

It counts the number of transmissions of message processing M_RECEIVE and M_SEND performed on the SX bus.

No, they won't. The programs will be executed from top to bottom for each task to which they are assigned, 'DEFAULT,' '

The four-axis pulse string output terminal module (Type_ NR1SF-HP4DT) does not have a physical ±OT terminal. You can s

Unfortunately, information in a device connected to the master module cannot be read even by building a user application

If battery-less operation is enabled under the 'CPU running definition' setting, the content of the retain memory is not

One possibility is that the compare value is not stored in the compare register of the high-speed counter. The compare v

Search by category

Keyword Search

FAQ within [ PLC ]

381-390 of Total 398

≪ 39 / 40page ≫

When using Cfr32, are the start code, end code, and BCC included in the maximum data size?

Yes, they are. The maximum size is 32 words including the actual data, start code, end code, and BCC. (The same applies to _Cfr64, _Cfr128, _Cfr252, and _Cfr... Show Detail
- No：1495
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
The version of the D300win is displayed as Version 4.0. Why?

This was probably caused by the following factors (1) The PC was not restarted after the D300win was installed. (2) A space is included in the name of the... Show Detail
- No：1441
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
How many units of Ethernet module (Type_ NP1L-ET□) can be used in a system?

Up to 4 units can be connected in 1 configuration (on 1 SX bus). Note, however, that they must be configured so that the total number of units of other comm... Show Detail
- No：1395
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
I understand that an analog input module (Type_ NP1AXH4-MR, etc.) has a signal line breakage detection function. How does it work?

For an analog input range (1 to 5 V or 4 to 20 mA), a line breakage detection function is provided. An input voltage of 0.92 V or lower for the 1 to 5 V ran... Show Detail
- No：1316
- Displayed Date：2023/04/25 19:00
- Category： I/O
What does the sending/receiving counter for the structure variable RAS.RAS of the non-procedure standard expansion FB for communication _Cfr* count...

It counts the number of transmissions of message processing M_RECEIVE and M_SEND performed on the SX bus. Show Detail
- No：1569
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
When I create multiple programs in the program configuration with the D300win, will these programs be executed in the order shown in the program co...

No, they won't. The programs will be executed from top to bottom for each task to which they are assigned, 'DEFAULT,' 'FIXED_CYCLE' and 'EVENT' respectively. Show Detail
- No：1538
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
I want to connect wiring for ±OT input with the four-axis pulse string output terminal module (Type_ NR1SF-HP4DT) but the unit does not have the te...

The four-axis pulse string output terminal module (Type_ NR1SF-HP4DT) does not have a physical ±OT terminal. You can solve this problem by using software a... Show Detail
- No：1447
- Displayed Date：2023/04/25 19:00
- Category： Function
Is there any way to check the vendor ID, product code, product revision, serial No., etc. of the slave from the DeviceNet master module (Type_ NP1L...

Unfortunately, information in a device connected to the master module cannot be read even by building a user application. Please use the dedicated configura... Show Detail
- No：1387
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
The variables I specified as retained by using D300win are not retained through a power failure. What can I do to solve the problem?

If battery-less operation is enabled under the 'CPU running definition' setting, the content of the retain memory is not retained. Disable battery-less opera... Show Detail
- No：1350
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:36
- Category： Support tool (D300win)
I use the high-speed counter module (Type_ NP1F-HC2) FB. The compare value is larger than the present counter value but the compare output becomes ...

One possibility is that the compare value is not stored in the compare register of the high-speed counter. The compare value is written by turning the data w... Show Detail
- No：1309
- Displayed Date：2023/04/25 19:00
- Category： Function

381-390 of Total 398

PLC

Common to N
- Support tool (Others)
Common to SX
- Support tool (D300win)
- |Application
- |Support tool
- |Support tool (Standard)
- |Others
- |Accessory
- |Error
- |Communication (T-link)
- |Function
- |Communication (Others)
- |Main unit
- |Communication (Ethernet)

SPB
SPF
- Others
- |Support tool
- |Communication (Ethernet)
- |Communication (Others)
- |Main unit
- |Application

SPH
- Communication (T-link)
- |Support tool (D300win)
- |Others
- |Communication (Others)
- |Main unit
- |Function
- |Communication (Ethernet)
- |Application
- |Accessory
- |Support tool (Standard)
- |I/O
- |Error
- |Support tool

Info & News

To Top of Page

PLC

Regional Websites

About Us

Products & Solutions

Investor Relations

Sustainability

Latest FAQ

GLOBAL

Search by category

Keyword Search

FAQ within [ PLC ]

PLC

Info & News