All the channels in the high-speed output module are set to the general purpose output mode (normal digital output) by d

RS-485 is upper compatible with RS-422. In general, RS-422 devices mainly use 4-wire connection method, while RS-485 dev

You can connect an SX series CPU to D300win via USB, Ethernet or a dedicated loader cable, depending on the model. Confi

Possible causes are as follows: 1) The baud rate differs between the PLC and the target device. 2) The stop bit differ

R_STS = 1 means 'send buffer overflow' detected by the general-purpose communication module. Check the communication for

Both Standard and Expert (D300win) are program loader software for the SX series. However, there is no compatibility be

Check that the terminating plug is attached. Check also that the SX bus expansion cable is not broken. You need to att

You don't need a dedicated cable. Since the parameters will be set via the CPU module, you need a loader cable for the

The following loader software, connection cable, and converter are required. 1) Loader software ・NP4H-SWN The pro

They cannot be monitored if the number of rows in the variable worksheet exceeds 2520. Divide the variable worksheet so

Search by category

Keyword Search

FAQ within [ PLC ]

11-20 of Total 398

≪ 2 / 40page ≫

How do I perform pulse output with the high-speed output module (Type_NP1Y32T09P1-A)?

All the channels in the high-speed output module are set to the general purpose output mode (normal digital output) by default. To use the module in the pul... Show Detail
- No：1613
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:59
- Category： Function
What is the difference between RS-485 and RS-422 ?

RS-485 is upper compatible with RS-422. In general, RS-422 devices mainly use 4-wire connection method, while RS-485 devices mainly use 2-wire connection met... Show Detail
- No：1521
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
I would like to read and write data by the SX-Programmer Expert (D300win). How do I configure the communication settings for SPH series CPUs?

You can connect an SX series CPU to D300win via USB, Ethernet or a dedicated loader cable, depending on the model. Configure the communication settings acco... Show Detail
- No：1509
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:41
- Category： Support tool (D300win)
A communication error occurred, saying it was caused by a framing error. What causes a framing error?

Possible causes are as follows: 1) The baud rate differs between the PLC and the target device. 2) The stop bit differs between the PLC and the target devi... Show Detail
- No：1275
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 14:13
- Category： Communication (Others)
When the MODBUS master standard expansion FB _C_modm operates, the receive status becomes R_STS = 1. This is not shown in the receive status list. ...

R_STS = 1 means 'send buffer overflow' detected by the general-purpose communication module. Check the communication format, communication interval and other... Show Detail
- No：1607
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
I want to edit the program of the PLC (SX series). In the catalogue and website, I found that two types of program loaders, Standard and Expert (D3...

Both Standard and Expert (D300win) are program loader software for the SX series. However, there is no compatibility between program data (called 'project')... Show Detail
- No：1646
- Displayed Date：2023/04/25 19:00
- Category： Support tool
In the diagnostic screen, error message 'Fatal failure SX bus error Time up error of deciding SBM use mode' appeared. What are the possible cause...

Check that the terminating plug is attached. Check also that the SX bus expansion cable is not broken. You need to attach an SX bus terminating plug at bot... Show Detail
- No：1648
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?

You don't need a dedicated cable. Since the parameters will be set via the CPU module, you need a loader cable for the PLC and the program loader software. Show Detail
- No：1676
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
I would like to read and write programs of the SPB series SX mode on a personal computer (Windows 10). What loader software and connection cable ar...

The following loader software, connection cable, and converter are required. 1) Loader software ・NP4H-SWN The product CD of NP4H-SWN includes the lo... Show Detail
- No：1510
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:42
- Category： Support tool
With D300win V2, I cannot monitor some of the variables in the global variable worksheet.

They cannot be monitored if the number of rows in the variable worksheet exceeds 2520. Divide the variable worksheet so that the number of rows is 2500 or... Show Detail
- No：1384
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 16:16
- Category： Support tool (D300win)