The LG terminal is a line filter ground terminal in the power supply module. It is intended for guiding any external noi

The EN and ENO terminals of functions mean the start operation terminal and the operation result terminal, respectively.

Yes, all points can be used. Regarding the pulse width, pulse signals with a width down to 20 us can be captured with po

It counts the number of transmissions of message processing M_RECEIVE and M_SEND performed on the SX bus.

Set the I/O area of the positioning module following the steps below. 1) Set 'h1C00' in the offset word address +16 (Ch

This was probably caused by one of the following two factors_ (1) ±OT is set to 'Disabled' in the parameter setting of

For setting parameter values (such as P, I and D), it is possible to_ (1) Set the data within the user application

The counter is initially set to gate mode. Counting is disabled unless you provide a 'gate signal' externally by hardwar

Set the number of timers according to the number actually used. By simply specifying 8192 or a larger value as the tim

During battery-less operation, previous fault information and other 'history of RAS' are not saved. Only the present RAS

Search by category

Keyword Search

FAQ within [ PLC ]

1-10 of Total 398

≪ 1 / 40page ≫

What is the difference between the LG and FG terminals of the power supply module (Type_ NP1S-22)?

The LG terminal is a line filter ground terminal in the power supply module. It is intended for guiding any external noise produced in the power supply or sw... Show Detail
- No：1374
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 10:52
- Category： Main unit
What is the meaning of EN and ENO of functions in Expert (D300win)?

The EN and ENO terminals of functions mean the start operation terminal and the operation result terminal, respectively. ・When the variable connected to the... Show Detail
- No：1476
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:31
- Category： Support tool (D300win)
When the pulse catch function of the high-speed input module (Type_ NP1X3206-A) is used, can all points be used? Is any difference made to the puls...

Yes, all points can be used. Regarding the pulse width, pulse signals with a width down to 20 us can be captured with ports 1 to 8. With ports 9 to 32, pu... Show Detail
- No：1321
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:17
- Category： Function
What does the sending/receiving counter for the structure variable RAS.RAS of the non-procedure standard expansion FB for communication _Cfr* count...

It counts the number of transmissions of message processing M_RECEIVE and M_SEND performed on the SX bus. Show Detail
- No：1569
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
How do I use a manual pulse generator with the positioning module (Type_NP1F-MP2/MA2)?

Set the I/O area of the positioning module following the steps below. 1) Set 'h1C00' in the offset word address +16 (Ch1 Set value area: Low word). (Set ... Show Detail
- No：1396
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:17
- Category： Function
Although the LED for ±OT lights up on the positioning control module (Type_ NP1F-MP2/MA2), the positioning operation finishes. What is the causal f...

This was probably caused by one of the following two factors_ (1) ±OT is set to 'Disabled' in the parameter setting of the positioning control module (Type_... Show Detail
- No：1575
- Displayed Date：2023/04/25 19:00
- Category： Function
For PID control by using a PID FB package, how should I set the various parameters?

For setting parameter values (such as P, I and D), it is possible to_ (1) Set the data within the user application (2) Use 'PID FB parameter support ut... Show Detail
- No：1296
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 14:18
- Category： Function
I used the high-speed counter module (Type_NP1F-HC2) but it doesn't count. I didn't make any settings in particular.

The counter is initially set to gate mode. Counting is disabled unless you provide a 'gate signal' externally by hardware or set 'gate disabled' by software.... Show Detail
- No：1541
- Displayed Date：2023/04/25 19:00
- Category： Function
A global timer with the Standard Loader, T8192 or a larger value must be specified as the timer address. Do I need to set the number of timers as 8...

Set the number of timers according to the number actually used. By simply specifying 8192 or a larger value as the timer number, a global timer can be used. Show Detail
- No：1635
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
When you use battery-less operation on the SPH, is the history of RAS information recorded?

During battery-less operation, previous fault information and other 'history of RAS' are not saved. Only the present RAS information is displayed. Show Detail
- No：1579
- Displayed Date：2023/04/25 19:00
- Category： Main unit