When you use preset operation in the linear operation mode, counting is sometimes discontinued due to preset overflow.

For setting parameter values (such as P, I and D), it is possible to_ (1) Set the data within the user application (2)

The module is equipped with 2 channels of high-speed counter and signals of a different voltage can be counted for each

Use the recommended shielded twisted pair cable mentioned in the User's Manual. Also provide shielding.

When the CPU module is stopped, the positioning operation stops.

In the MV selection part in the PID FB, (1) the backward operation uses the internally calculated MV value (%) without p

Check the following points_ (1) Check the input form specified on the application program. (2) Set Enable counting to

Only open-collector (single-ended) signals are accepted. (NP1F-HC2 accepts differential signals.) The rated current is

If the start bit remains on, the positioning end signal is not generated.

The flashing of the LED of the high-speed output module (Type_ NP1Y32T09P1-A) indicates that pulse output is generated.

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC > SPH > Function

Latest FAQ

When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
When I switch the CPU module from RUN to STOP while the four-axis pulse output unit (NR1SF-HP4DT) is outputting pulses, does the positioning operat...
With a counter module (NP1F-HC2), I use ２ counter FBs to control 2 channels. At system start-up, I set simultaneous preset operations for the 2 cha...
What is the difference between the PID forward and backward operations when the PID FB package is used?
How can I detect a low battery voltage of the SRAM card with the memory card interface module (Type_ NP1F-MM1)?

GLOBAL

Search by category

Keyword Search

FAQ within [ Function ]

1-10 of Total 50

≪ 1 / 5page ≫

When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...

When you use preset operation in the linear operation mode, counting is sometimes discontinued due to preset overflow. Show Detail
- No：1675
- Displayed Date：2023/04/25 19:00
For PID control by using a PID FB package, how should I set the various parameters?

For setting parameter values (such as P, I and D), it is possible to_ (1) Set the data within the user application (2) Use 'PID FB parameter support ut... Show Detail
- No：1296
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 14:18
I understand that the high-speed counter module (Type_ NP1F-HC2MR) is capable of counting pulses of 5 V/12 V/24 V. Is it possible to count with a d...

The module is equipped with 2 channels of high-speed counter and signals of a different voltage can be counted for each channel. To set the signal level, s... Show Detail
- No：1398
- Displayed Date：2023/04/25 19:00
What measures can I take against external noise of the high-speed counter (Type_ NP1F-HC2)?

Use the recommended shielded twisted pair cable mentioned in the User's Manual. Also provide shielding. Show Detail
- No：1365
- Displayed Date：2023/04/25 19:00
When I switch the CPU module from RUN to STOP while the four-axis pulse output unit (NR1SF-HP4DT) is outputting pulses, does the positioning operat...

When the CPU module is stopped, the positioning operation stops. Show Detail
- No：1669
- Displayed Date：2023/04/25 19:00
What is the difference between the PID forward and backward operations when the PID FB package is used?

In the MV selection part in the PID FB, (1) the backward operation uses the internally calculated MV value (%) without processing it (as-is)_ and (2) the for... Show Detail
- No：1625
- Displayed Date：2023/04/25 19:00
Pulse counting is disabled on the high-speed input module (Type_ NP1X3206-A). What should I check?

Check the following points_ (1) Check the input form specified on the application program. (2) Set Enable counting to '1.' If the pulse count data regist... Show Detail
- No：1570
- Displayed Date：2023/04/25 19:00
Is it possible to count differential input pulses using a high-speed digital input module (Type_ NP1X3206-A)?

Only open-collector (single-ended) signals are accepted. (NP1F-HC2 accepts differential signals.) The rated current is 40 mA and an encoder that permits t... Show Detail
- No：1373
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:43
With the pulse train output positioning control module (Type_ NP1F-HP2), positioning has ended but the end signal is not generated.

If the start bit remains on, the positioning end signal is not generated. Show Detail
- No：1317
- Displayed Date：2023/04/25 19:00
With the high-speed output module (Type_ NP1Y32T09P1-A), the LED flashes but no pulse is output to the outside. What should I check?

The flashing of the LED of the high-speed output module (Type_ NP1Y32T09P1-A) indicates that pulse output is generated. If no pulse output is generated in t... Show Detail
- No：1291
- Displayed Date：2023/04/25 19:00

1-10 of Total 50

Info & News

To Top of Page

PKSHA FAQ logo

Function

Regional Websites

About Us

Products & Solutions

Investor Relations

Sustainability