No, it is not possible. Combine the electronic cam FB package (Type_ NP4N-CAMFV3) with a positioning control module (Typ

You cannot use software filters when you use the pulse counter input function of the high-speed input module (Type_ NP1X

If the start bit remains on, the positioning end signal is not generated.

A possible cause is that a “Deviation amount over error” occurred. For details, refer to the user's manual FEH213 (NP1F-

Use the recommended shielded twisted pair cable mentioned in the User's Manual. Also provide shielding.

Since the parameter data area of the positioning control module (Type_ NP1F-MP2/MA2) operates on the RAM, it is always c

You can refer to sample project Mptpf4.zwt stored in the ZIPPED folder in the D300win folder.

The near zero signal/command pulse zero signal/positioning end signal/RDY signal of the status information signals are s

The MICREX-SX series positioning module 'Type_NP1F-HD2A' replaces NC1F-VP1/FGU130B. Be aware of the following points:

Check the following two points (1) To use the EMG/±OT signal, input the 'External power supply 24 V DC.' (2) Check the

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC > SPH > Function

Latest FAQ

When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
When I switch the CPU module from RUN to STOP while the four-axis pulse output unit (NR1SF-HP4DT) is outputting pulses, does the positioning operat...
With a counter module (NP1F-HC2), I use ２ counter FBs to control 2 channels. At system start-up, I set simultaneous preset operations for the 2 cha...
What is the difference between the PID forward and backward operations when the PID FB package is used?
How can I detect a low battery voltage of the SRAM card with the memory card interface module (Type_ NP1F-MM1)?

GLOBAL

Search by category

Keyword Search

FAQ within [ Function ]

1-10 of Total 50

≪ 1 / 5page ≫

Is electronic cam operation possible without using the dedicated module?

No, it is not possible. Combine the electronic cam FB package (Type_ NP4N-CAMFV3) with a positioning control module (Type_ NP1F-MP2/MA2). Show Detail
- No：1334
- Displayed Date：2023/04/25 19:00
When I use the pulse counter input function of the high-speed input module (Type_ NP1X3206-A), can I set software filters?

You cannot use software filters when you use the pulse counter input function of the high-speed input module (Type_ NP1X3206-A). Show Detail
- No：1599
- Displayed Date：2023/04/25 19:00
With the pulse train output positioning control module (Type_ NP1F-HP2), positioning has ended but the end signal is not generated.

If the start bit remains on, the positioning end signal is not generated. Show Detail
- No：1317
- Displayed Date：2023/04/25 19:00
On the positioning module (Type_NP1F-MP2/MA2), the 'ERR' LED turns ON. What are the possible causes?

A possible cause is that a “Deviation amount over error” occurred. For details, refer to the user's manual FEH213 (NP1F-MA2) or FEH214 (NP1F-MP2) 'Section 8 ... Show Detail
- No：1290
- Displayed Date：2023/04/25 19:00
What measures can I take against external noise of the high-speed counter (Type_ NP1F-HC2)?

Use the recommended shielded twisted pair cable mentioned in the User's Manual. Also provide shielding. Show Detail
- No：1365
- Displayed Date：2023/04/25 19:00
When I turned on the positioning control module (Type_ NP1F-MP2/MA2) in the morning, the parameters were reset to the initial values. What is the f...

Since the parameter data area of the positioning control module (Type_ NP1F-MP2/MA2) operates on the RAM, it is always cleared when you turn off the module. ... Show Detail
- No：1573
- Displayed Date：2023/04/25 19:00
Do you have a connection example for the input variable of the compact positioning FB of the positioning FB package?

You can refer to sample project Mptpf4.zwt stored in the ZIPPED folder in the D300win folder. Show Detail
- No：1614
- Displayed Date：2023/04/25 19:00
With a positioning control module (Type_ NP1F-MP2/MA2), what are the statuses of the status information signals after power-up?

The near zero signal/command pulse zero signal/positioning end signal/RDY signal of the status information signals are set to [1]. The interrupt input sig... Show Detail
- No：1318
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:17
I use the MICREX-F series positioning module (Type_NC1F-VP1/FGU130B). What replaces it? Is there anything to be aware of when replacing it?

The MICREX-SX series positioning module 'Type_NP1F-HD2A' replaces NC1F-VP1/FGU130B. Be aware of the following points: 1) NP1F-HD2A is differential output t... Show Detail
- No：1463
- Displayed Date：2023/04/25 19:00
When I turned on the positioning control module (Type_ NP1F-MP2/MA2), the EMG/±OT LED lights up and positioning operation is disabled. What causes ...

Check the following two points (1) To use the EMG/±OT signal, input the 'External power supply 24 V DC.' (2) Check the wiring of the external equipment. (T... Show Detail
- No：1601
- Displayed Date：2023/04/25 19:00

1-10 of Total 50

Info & News

To Top of Page

PKSHA FAQ logo

Function

Regional Websites

About Us

Products & Solutions

Investor Relations

Sustainability