-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
- When I switch the CPU module from RUN to STOP while the four-axis pulse output unit (NR1SF-HP4DT) is outputting pulses, does the positioning operat...
- With a counter module (NP1F-HC2), I use ２ counter FBs to control 2 channels. At system start-up, I set simultaneous preset operations for the 2 cha...
- What is the difference between the PID forward and backward operations when the PID FB package is used?
- How can I detect a low battery voltage of the SRAM card with the memory card interface module (Type_ NP1F-MM1)?
GLOBAL
Search by category
Keyword Search
FAQ within [ Function ]
-
How do I perform pulse output with the high-speed output module (Type_NP1Y32T09P1-A)?
All the channels in the high-speed output module are set to the general purpose output mode (normal digital output) by default. To use the module in the pul... Show Detail
- No：1613
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:59
-
Check the following two points (1) To use the EMG/±OT signal, input the 'External power supply 24 V DC.' (2) Check the wiring of the external equipment. (T... Show Detail
- No：1601
- Displayed Date：2023/04/25 19:00
-
In the standard expansion counter FB _MHCNTH, CH0 operates but CH1 does not.
It seems that this problem was caused by an improper address setting for INDAT/OUTDAT assigned to the counter FB terminal. On a single module, assign the sa... Show Detail
- No：1539
- Displayed Date：2023/04/25 19:00
-
The MICREX-SX series positioning module 'Type_NP1F-HD2A' replaces NC1F-VP1/FGU130B. Be aware of the following points: 1) NP1F-HD2A is differential output t... Show Detail
- No：1463
- Displayed Date：2023/04/25 19:00
-
It might be counting noise as a pulse. Take the following measures_ (1) Isolate the pulse generator and PLC from the noise source and shorten the wiring dist... Show Detail
- No：1427
- Displayed Date：2023/04/25 19:00
-
The near zero signal/command pulse zero signal/positioning end signal/RDY signal of the status information signals are set to [1]. The interrupt input sig... Show Detail
- No：1318
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:17
-
You cannot use software filters when you use the pulse counter input function of the high-speed input module (Type_ NP1X3206-A). Show Detail
- No：1599
- Displayed Date：2023/04/25 19:00
-
The counter is initially set to gate mode. Counting is disabled unless you provide a 'gate signal' externally by hardware or set 'gate disabled' by software.... Show Detail
- No：1541
- Displayed Date：2023/04/25 19:00
-
In the PID FB, why is the integration time set by the number of periods and not by ms?
The PID FB is assumed to be processed in a periodic task. The integration time is calculated by multiplying the periodic task period in ms by the number of p... Show Detail
- No：1390
- Displayed Date：2023/04/25 19:00
-
The minimum required products are (1) High-performance CPU exclusively for the electronic cam, (2) pulse train combined module (Type_ NP1F-MP2) or anal... Show Detail
- No：1323
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:20
31-40 of Total 50