-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
- When I switch the CPU module from RUN to STOP while the four-axis pulse output unit (NR1SF-HP4DT) is outputting pulses, does the positioning operat...
- With a counter module (NP1F-HC2), I use ２ counter FBs to control 2 channels. At system start-up, I set simultaneous preset operations for the 2 cha...
- What is the difference between the PID forward and backward operations when the PID FB package is used?
- How can I detect a low battery voltage of the SRAM card with the memory card interface module (Type_ NP1F-MM1)?
GLOBAL
Search by category
Keyword Search
FAQ within [ Function ]
-
It might be counting noise as a pulse. Take the following measures_ (1) Isolate the pulse generator and PLC from the noise source and shorten the wiring dist... Show Detail
- No：1427
- Displayed Date：2023/04/25 19:00
-
When the EMG signal and ±OT signal are not used, connect them to 24 V DC. Alternatively, you can set the ±OT signal to 'Disabled' in the parameter settings ... Show Detail
- No：1432
- Displayed Date：2023/04/25 19:00
-
When the CPU module is stopped, the positioning operation stops. Show Detail
- No：1669
- Displayed Date：2023/04/25 19:00
-
In PPID, a POU for the PID FB package, which range does the % of proportional band P account for?
Proportional band P is the % of the variation range of input PV required for the change of output MV in the effective variation range from 0 to 100%. It is... Show Detail
- No：1580
- Displayed Date：2023/04/25 19:00
-
On the positioning module (Type_NP1F-MP2/MA2), the 'ERR' LED turns ON. What are the possible causes?
A possible cause is that a “Deviation amount over error” occurred. For details, refer to the user's manual FEH213 (NP1F-MA2) or FEH214 (NP1F-MP2) 'Section 8 ... Show Detail
- No：1290
- Displayed Date：2023/04/25 19:00
-
How do I use a manual pulse generator with the positioning module (Type_NP1F-MP2/MA2)?
Set the I/O area of the positioning module following the steps below. 1) Set 'h1C00' in the offset word address +16 (Ch1 Set value area: Low word). (Set ... Show Detail
- No：1396
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:17
-
How do I perform pulse output with the high-speed output module (Type_NP1Y32T09P1-A)?
All the channels in the high-speed output module are set to the general purpose output mode (normal digital output) by default. To use the module in the pul... Show Detail
- No：1613
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:59
-
Since the parameter data area of the positioning control module (Type_ NP1F-MP2/MA2) operates on the RAM, it is always cleared when you turn off the module. ... Show Detail
- No：1573
- Displayed Date：2023/04/25 19:00
-
While NP1F-HC2 requires an external power supply of 5 V DC, NP1F-HC8 produces 5 V DC within the module from an external 24 V DC power supply and does not req... Show Detail
- No：1341
- Displayed Date：2023/04/25 19:00
-
In the standard expansion counter FB _MHCNTH, CH0 operates but CH1 does not.
It seems that this problem was caused by an improper address setting for INDAT/OUTDAT assigned to the counter FB terminal. On a single module, assign the sa... Show Detail
- No：1539
- Displayed Date：2023/04/25 19:00
31-40 of Total 50