-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- I have configured a multi-CPU system, but the system has run out of memory for the multi-CPU. Can I access the common general memory from the other...
- What is the rated current value of the fuse in the power supply module (NP1S-22)? I want to know to select the circuit breaker on the primary side ...
- When I mount the user ROM card for the SPH200 (Type_ NP8PMF-16) without changing its write protection from OFF, is the content of the ROM protected?
- When the retain memory (memory for data backup with a battery) of the CPU module of the MICREX-SX Series SPH is corrupted, how does the CPU module ...
- Can I mount or remove a CPU module and a power supply module on a hot plug base board while the system power is on?
GLOBAL
Search by category
Keyword Search
FAQ within [ Main unit ]
-
How can I write to the user ROM card of a standard CPU?
Turn off the write-protect switch of the user ROM card, mount it on the CPU module and transfer a program to write it to the user ROM card. Show Detail
- No：1344
- Displayed Date：2023/04/25 19:00
-
For what application is the base board with station number setting switch used?
It is used as a base specified for 'system fail-soft start-up' operation, which is set when there is any base with some modules on which power is not turned ... Show Detail
- No：1411
- Displayed Date：2023/04/25 19:00
-
The SX bus connector of the SPH300EX (Type_ NP1PS-74D) is an OUT (output) connector. When you connect SX bus equipment, connect the cable to the IN (input)... Show Detail
- No：1535
- Displayed Date：2023/04/25 19:00
-
Is it permitted to have an unused slot in an SPH system configuration?
An unused slot is permitted in a system configuration. If you plan to mount a module in the unused slot in the future, it can be registered as 'unimplemen... Show Detail
- No：1313
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 14:32
-
No, it doesn't. A power supply module may occupy two slots (Type_ NP1S-22, NP1S-42) or one slot (Type_ NP1S-81, NP1S-91). The connector at the far left... Show Detail
- No：1340
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:34
-
No, they do not have polarity because they use relay contacts. Show Detail
- No：1585
- Displayed Date：2023/04/25 19:00
-
Can I store multiple programs in the user ROM card (CF or SD) ?
No, it is not possible. Only one program can be stored. Show Detail
- No：1298
- Displayed Date：2023/04/25 19:00
-
When you use battery-less operation on the SPH, is the history of RAS information recorded?
During battery-less operation, previous fault information and other 'history of RAS' are not saved. Only the present RAS information is displayed. Show Detail
- No：1579
- Displayed Date：2023/04/25 19:00
-
The SPH does not have a RUN contact. Is there any alternative?
As an alternative, you can combine hardware and software functions. (1) Hardware_ Prepare a relay output card and use one point as a RUN contact. (2) Sof... Show Detail
- No：1587
- Displayed Date：2023/04/25 19:00
-
When the memory with a retain attribute is corrupted, the CPU clears the memory and operates in nonfatal fault condition. If the power is reset again in this... Show Detail
- No：1611
- Displayed Date：2023/04/25 19:00
1-10 of Total 34