Selecting the DCE mode for the communication parameter_ DCE designation keeps DSR always on.

Unfortunately, information in a device connected to the master module cannot be read even by building a user application

Yes, they are. The maximum size is 32 words including the actual data, start code, end code, and BCC. (The same applies

The area is cleared when the power supply is turned off once and turned on again. The P/PE link memory is located in th

Set the port No. as described below. (1) For NP1L-RS2_ Set '0.' (2) For NP1L-RS4_ Set '1.' See the figure below for th

It counts the number of transmissions of message processing M_RECEIVE and M_SEND performed on the SX bus.

The existing MICREX-F program does not need any modification.

Use the following types of configurators: 'CONF-PDP' for NP1L-PD1 and 'NetTool for Profibus' for NP1L-PD2. Purchase a co

It takes place only when data are received from an external device.

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC > SPH > Communication (Others)

Latest FAQ

When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
I use DeviceNet interface module (NP1L-RD1) under DeviceNet master (NP1L-DN1). How can I specify NP1L-RD1 in the system definition?
In the communication module (NP1L-RS1/RS2/RS3/RS4/RS5), is it possible to change communication parameter such as fixed length to variable length af...
With the FL-net module (NP1L-FL1/FL2/FL3), is there any way to confirm that the data sent from the node-A have actually been received by the node-B?

GLOBAL

Search by category

Keyword Search

FAQ within [ Communication (Others) ]

1-10 of Total 53

≪ 1 / 6page ≫

When does the port status_ DSR (data set ready) in a structure variable_ RAS of the non-procedural standard expansion FB for communication remain on?

Selecting the DCE mode for the communication parameter_ DCE designation keeps DSR always on. Show Detail
- No：1297
- Displayed Date：2023/04/25 19:00
Is there any way to check the vendor ID, product code, product revision, serial No., etc. of the slave from the DeviceNet master module (Type_ NP1L...

Unfortunately, information in a device connected to the master module cannot be read even by building a user application. Please use the dedicated configura... Show Detail
- No：1387
- Displayed Date：2023/04/25 19:00
When using Cfr32, are the start code, end code, and BCC included in the maximum data size?

Yes, they are. The maximum size is 32 words including the actual data, start code, end code, and BCC. (The same applies to _Cfr64, _Cfr128, _Cfr252, and _Cfr... Show Detail
- No：1495
- Displayed Date：2023/04/25 19:00
In the P/PE link area, is the send area of the local station cleared when the power supply is turned off once and turned on again? Is there any set...

The area is cleared when the power supply is turned off once and turned on again. The P/PE link memory is located in the built-in memory (RAM) of the P/PE-l... Show Detail
- No：1436
- Displayed Date：2023/04/25 19:00
For the initial setting of a general-purpose communication module with only one communication port such as NP1L-RS2 and NP1L-RS4, is it correct to ...

Set the port No. as described below. (1) For NP1L-RS2_ Set '0.' (2) For NP1L-RS4_ Set '1.' See the figure below for the setting for each type of genera... Show Detail
- No：1383
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:45
What does the sending/receiving counter for the structure variable RAS.RAS of the non-procedure standard expansion FB for communication _Cfr* count...

It counts the number of transmissions of message processing M_RECEIVE and M_SEND performed on the SX bus. Show Detail
- No：1569
- Displayed Date：2023/04/25 19:00
An existing P-link system is composed of MICREX-F. If part of it is replaced with P-link of MICREX-SX, does the existing MICREX-F program need to b...

The existing MICREX-F program does not need any modification. Show Detail
- No：1319
- Displayed Date：2023/04/25 19:00
What is the type of the configurator that is used with NP1L-PD1/PD2?

Use the following types of configurators: 'CONF-PDP' for NP1L-PD1 and 'NetTool for Profibus' for NP1L-PD2. Purchase a configurator from HMS Industrial Networ... Show Detail
- No：1494
- Displayed Date：2023/04/25 19:00
Can I use both P-link and PE-link in one system?

No, you cannot. Show Detail
- No：1523
- Displayed Date：2023/04/25 19:00
When does the standard expansion FB for communication_ Cfrp2 refresh the port status in the structure variable_ RAS?

It takes place only when data are received from an external device. Show Detail
- No：1400
- Displayed Date：2023/04/25 19:00

1-10 of Total 53

Info & News

To Top of Page

PKSHA FAQ logo

Communication (Others)

Regional Websites

About Us

Products & Solutions

Investor Relations

Sustainability