-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
- When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
- I use DeviceNet interface module (NP1L-RD1) under DeviceNet master (NP1L-DN1). How can I specify NP1L-RD1 in the system definition?
- In the communication module (NP1L-RS1/RS2/RS3/RS4/RS5), is it possible to change communication parameter such as fixed length to variable length af...
- With the FL-net module (NP1L-FL1/FL2/FL3), is there any way to confirm that the data sent from the node-A have actually been received by the node-B?
GLOBAL
Search by category
Keyword Search
FAQ within [ Communication (Others) ]
-
Can I use a commercially available hub for FL-net modules?
We recommend you use an unmanaged switch, without B.S protection that is an industrial hub fulfilling the conditions of use for FL-net. * What is 'B.S'?... Show Detail
- No：1465
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:28
-
It is the same as the loader mode (mode switch 3) of the general-purpose communication module (Type_ NP1L-RS1/RS2/RS3/RS4/RS5). Show Detail
- No：1379
- Displayed Date：2023/04/25 19:00
-
NP1L-RS1/RS4/RS5 support RS-485. Can I use them for RS-422 devices?
Yes, you can use NP1L-RS1/RS4/RS5 for RS-422 devices. RS-485 is upper compatible with RS-422. There are two connection types for RS-422 devices: 2-wire conne... Show Detail
- No：1522
- Displayed Date：2023/04/25 19:00
-
How does the FL-net module (Type_ NP1L-FL1/FL2/FL3) clear the error history recorded in each memory?
Once an error history is generated, it is retained internally within the FL-net module and is cleared when the power is turned off and turned on again or whe... Show Detail
- No：1567
- Displayed Date：2023/04/25 19:00
-
In the system definition, group-type slave stations in any I/O configuration are registered as 'DeviceNet capsule.' In addition, the numbers of input and out... Show Detail
- No：1644
- Displayed Date：2023/04/25 19:00
-
When the common memory system is used, this can be achieved by handshaking with an application using part of the link memory. Without handshaking, it is not... Show Detail
- No：1638
- Displayed Date：2023/04/25 19:00
-
You don't need a dedicated cable. Since the parameters will be set via the CPU module, you need a loader cable for the PLC and the program loader software. Show Detail
- No：1676
- Displayed Date：2023/04/25 19:00
-
Are there any FL-net boards compatible with Windows 10?
※NP3L-FL3PXSの英文マニュアルなし。FAQの翻訳は実施したので、有効フラグOFFにして登録のみ実施。英文マニュアルを作った場合、公開する。（2021/1/22：光井、小笠原） NP3L-FL3PXS (PCI-Express-bus-based FL-net board) is compatible ... Show Detail
- No：1464
- Displayed Date：2023/04/25 19:00
-
The received data is cleared to 0. Therefore, be sure not to read (ignore) the data by application program. Reopening the FB (turning the 'OPEN' terminal fro... Show Detail
- No：1672
- Displayed Date：2023/04/25 19:00
-
The 'SND' and 'RCV' LEDs on the P-link module (Type_ NP1L-PL1) look dark. Is this a fault?
The LEDs of the P-link module (Type_ NP1L-PL1) are designed to blink quickly in accordance with the ON/OFF of a signal. Although they look dim to the human e... Show Detail
- No：1624
- Displayed Date：2023/04/25 19:00
41-50 of Total 53