It is not possible. Each module comply to following FL-net standards. NP1L-FL1 : FL-netVer1 NP1L-FL2 : FL-netVer2

When the P-link module is specified as 'unimplemented' and no P-link module exists in the system, attempting to access t

The base board that plays the role of a hub of optical converter modules is not represented in the system definitions.

The optical converter NP1L-OL1 is an optical converter of the SX bus. It cannot be used because the SX bus is not a lin

The bus can be extended with the SX bus electrical repeater (Type_ NP2L-RP1). Up to three repeaters can be used in one

※NP3L-FL3PXSの英文マニュアルなし。FAQの翻訳は実施したので、有効フラグOFFにして登録のみ実施。英文マニュアルを作った場合、公開する。（2021/1/22：光井、小笠原） NP3L-FL3PXS (PCI-Express-bu

The area is cleared when the power supply is turned off once and turned on again. The P/PE link memory is located in th

The number of M_OPEN FBs that can be opened simultaneously is limited to 56. The number of FBs that can be simultaneousl

It is full duplex for both hardware and software (firmware) for anything other than communication by M_RECEIVE and M_SEN

In MICREX-SX, a scan list is automatically created by registering the remote I/O to be connected to the master module in

Font Size
S
M
L

GLOBAL > PLC > SPH > Communication (Others)

Latest FAQ

When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
I use DeviceNet interface module (NP1L-RD1) under DeviceNet master (NP1L-DN1). How can I specify NP1L-RD1 in the system definition?
In the communication module (NP1L-RS1/RS2/RS3/RS4/RS5), is it possible to change communication parameter such as fixed length to variable length af...
With the FL-net module (NP1L-FL1/FL2/FL3), is there any way to confirm that the data sent from the node-A have actually been received by the node-B?

GLOBAL

Search by category

Keyword Search

FAQ within [ Communication (Others) ]

31-40 of Total 53

≪ 4 / 6page ≫

Can we use an FL-net module (Type_ NP1L-FL1/FL2/FL3) and standard LAN device with same network?

It is not possible. Each module comply to following FL-net standards. NP1L-FL1 : FL-netVer1 NP1L-FL2 : FL-netVer2 NP1L-FL3 : FL-netVer3(Class1) In FL-... Show Detail
- No：1416
- Displayed Date：2023/04/25 19:00
In an SPH system, I specified the P-link module as 'unimplemented' and the program execution time was extended. Why?

When the P-link module is specified as 'unimplemented' and no P-link module exists in the system, attempting to access the P-link memory using a contact, coi... Show Detail
- No：1355
- Displayed Date：2023/04/25 19:00
Is there anything I should take note of when using an optical converter module (Type_ NP1L-OL1/OL2) as a hub on one base board?

The base board that plays the role of a hub of optical converter modules is not represented in the system definitions. When the power supply (PS) of the sam... Show Detail
- No：1351
- Displayed Date：2023/04/25 19:00
Is it possible to use the optical converter NP1L-OL1 between processors as with the P-link?

The optical converter NP1L-OL1 is an optical converter of the SX bus. It cannot be used because the SX bus is not a link between processors. Show Detail
- No：1327
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:31
The total extension of the SX bus has exceeded 25 m. Is there anything to relay the connection?

The bus can be extended with the SX bus electrical repeater (Type_ NP2L-RP1). Up to three repeaters can be used in one system. (When three repeaters are us... Show Detail
- No：1550
- Displayed Date：2023/04/25 19:00
Are there any FL-net boards compatible with Windows 10?

※NP3L-FL3PXSの英文マニュアルなし。FAQの翻訳は実施したので、有効フラグOFFにして登録のみ実施。英文マニュアルを作った場合、公開する。（2021/1/22：光井、小笠原） NP3L-FL3PXS (PCI-Express-bus-based FL-net board) is compatible ... Show Detail
- No：1464
- Displayed Date：2023/04/25 19:00
In the P/PE link area, is the send area of the local station cleared when the power supply is turned off once and turned on again? Is there any set...

The area is cleared when the power supply is turned off once and turned on again. The P/PE link memory is located in the built-in memory (RAM) of the P/PE-l... Show Detail
- No：1436
- Displayed Date：2023/04/25 19:00
Is there any limitation on the number of M_OPENs to be executed simultaneously? If there is a limitation, what is the maximum number?

The number of M_OPEN FBs that can be opened simultaneously is limited to 56. The number of FBs that can be simultaneously opened for each module depends on t... Show Detail
- No：1435
- Displayed Date：2023/04/25 19:00
With a general-purpose communication module, is RS232C completely full duplex?

It is full duplex for both hardware and software (firmware) for anything other than communication by M_RECEIVE and M_SEND on the SX bus, which are FB interna... Show Detail
- No：1413
- Displayed Date：2023/04/25 19:00
With the DeviceNet master module (Type_ NP1L-DN1), how can I create a scan list and register it with the master module?

In MICREX-SX, a scan list is automatically created by registering the remote I/O to be connected to the master module in the system configuration definitions... Show Detail
- No：1346
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:35

31-40 of Total 53

Info & News

To Top of Page

Communication (Others)

Regional Websites

About Us

Products & Solutions

Investor Relations

Sustainability