-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
- When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
- I use DeviceNet interface module (NP1L-RD1) under DeviceNet master (NP1L-DN1). How can I specify NP1L-RD1 in the system definition?
- In the communication module (NP1L-RS1/RS2/RS3/RS4/RS5), is it possible to change communication parameter such as fixed length to variable length af...
- With the FL-net module (NP1L-FL1/FL2/FL3), is there any way to confirm that the data sent from the node-A have actually been received by the node-B?
GLOBAL
Search by category
Keyword Search
FAQ within [ Communication (Others) ]
-
NP1L-RS1/RS4/RS5 support RS-485. Can I use them for RS-422 devices?
Yes, you can use NP1L-RS1/RS4/RS5 for RS-422 devices. RS-485 is upper compatible with RS-422. There are two connection types for RS-422 devices: 2-wire conne... Show Detail
- No：1522
- Displayed Date：2023/04/25 19:00
-
It is the same as the loader mode (mode switch 3) of the general-purpose communication module (Type_ NP1L-RS1/RS2/RS3/RS4/RS5). Show Detail
- No：1379
- Displayed Date：2023/04/25 19:00
-
Can I use a commercially available hub for FL-net modules?
We recommend you use an unmanaged switch, without B.S protection that is an industrial hub fulfilling the conditions of use for FL-net. * What is 'B.S'?... Show Detail
- No：1465
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:28
-
When the P-link module is specified as 'unimplemented' and no P-link module exists in the system, attempting to access the P-link memory using a contact, coi... Show Detail
- No：1355
- Displayed Date：2023/04/25 19:00
-
No, they are not synchronized. The configuration flag cannot be used for that application. Use the broadcast area for handshaking using the application to ... Show Detail
- No：1631
- Displayed Date：2023/04/25 19:00
-
What is the type of the configurator that is used with NP1L-PD1/PD2?
Use the following types of configurators: 'CONF-PDP' for NP1L-PD1 and 'NetTool for Profibus' for NP1L-PD2. Purchase a configurator from HMS Industrial Networ... Show Detail
- No：1494
- Displayed Date：2023/04/25 19:00
-
Can we use an FL-net module (Type_ NP1L-FL1/FL2/FL3) and standard LAN device with same network?
It is not possible. Each module comply to following FL-net standards. NP1L-FL1 : FL-netVer1 NP1L-FL2 : FL-netVer2 NP1L-FL3 : FL-netVer3(Class1) In FL-... Show Detail
- No：1416
- Displayed Date：2023/04/25 19:00
-
Set the port No. as described below. (1) For NP1L-RS2_ Set '0.' (2) For NP1L-RS4_ Set '1.' See the figure below for the setting for each type of genera... Show Detail
- No：1383
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:45
-
The total extension of the SX bus has exceeded 25 m. Is there anything to relay the connection?
The bus can be extended with the SX bus electrical repeater (Type_ NP2L-RP1). Up to three repeaters can be used in one system. (When three repeaters are us... Show Detail
- No：1550
- Displayed Date：2023/04/25 19:00
-
What is necessary for MODBUS_RTU communication between SPH and an external device?
The following are necessary. 1) Hardware: General-purpose communication module (NP1L-RS1/RS2/RS3/RS4/RS5) whose firmware version is V42 or later ... Show Detail
- No：1469
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:29
11-20 of Total 53