※NP3L-FL3PXSの英文マニュアルなし。FAQの翻訳は実施したので、有効フラグOFFにして登録のみ実施。英文マニュアルを作った場合、公開する。（2021/1/22：光井、小笠原） NP3L-FL3PXS (PCI-Express-bu

We recommend you use an unmanaged switch, without B.S protection that is an industrial hub fulfilling the conditions of

The following are necessary. 1) Hardware: General-purpose communication module (NP1L-RS1/RS2/RS3/RS4/RS5) whose fi

The bus can be extended with the SX bus electrical repeater (Type_ NP2L-RP1). Up to three repeaters can be used in one

No, it does not support the DPV1 function. It supports the DPV0 (I/O communication) function.

You cannot use a router because FL-net does not support the use of subnet. *Related document: For the notes on using FL

While 'DTR_ terminal ready' can be used with RS-232C, this control line is not present for RS-485. If no response is re

The optical converter NP1L-OL1 is an optical converter of the SX bus. It cannot be used because the SX bus is not a lin

When connected via 10BASE-T, you can replace it. There is no need to change the system definition. Before replacement, s

The MICREX-SX does not include a communication module having interfaces with Mitsubishi's original networks, MELSEC-NET/

Font Size
S
M
L

GLOBAL > PLC > SPH > Communication (Others)

Latest FAQ

When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
I use DeviceNet interface module (NP1L-RD1) under DeviceNet master (NP1L-DN1). How can I specify NP1L-RD1 in the system definition?
In the communication module (NP1L-RS1/RS2/RS3/RS4/RS5), is it possible to change communication parameter such as fixed length to variable length af...
With the FL-net module (NP1L-FL1/FL2/FL3), is there any way to confirm that the data sent from the node-A have actually been received by the node-B?

GLOBAL

Search by category

Keyword Search

FAQ within [ Communication (Others) ]

11-20 of Total 53

≪ 2 / 6page ≫

Are there any FL-net boards compatible with Windows 10?

※NP3L-FL3PXSの英文マニュアルなし。FAQの翻訳は実施したので、有効フラグOFFにして登録のみ実施。英文マニュアルを作った場合、公開する。（2021/1/22：光井、小笠原） NP3L-FL3PXS (PCI-Express-bus-based FL-net board) is compatible ... Show Detail
- No：1464
- Displayed Date：2023/04/25 19:00
Can I use a commercially available hub for FL-net modules?

We recommend you use an unmanaged switch, without B.S protection that is an industrial hub fulfilling the conditions of use for FL-net. * What is 'B.S'?... Show Detail
- No：1465
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:28
What is necessary for MODBUS_RTU communication between SPH and an external device?

The following are necessary. 1) Hardware: General-purpose communication module (NP1L-RS1/RS2/RS3/RS4/RS5) whose firmware version is V42 or later ... Show Detail
- No：1469
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:29
The total extension of the SX bus has exceeded 25 m. Is there anything to relay the connection?

The bus can be extended with the SX bus electrical repeater (Type_ NP2L-RP1). Up to three repeaters can be used in one system. (When three repeaters are us... Show Detail
- No：1550
- Displayed Date：2023/04/25 19:00
Does the PROFIBUS-DP master/slave module (Type_ NP1L-PD1/PS1) support the DPV1 (message communication) function?

No, it does not support the DPV1 function. It supports the DPV0 (I/O communication) function. Show Detail
- No：1391
- Displayed Date：2023/04/25 19:00
Can I use a router for FL-net?

You cannot use a router because FL-net does not support the use of subnet. *Related document: For the notes on using FL-net, refer to 'Appendix 2-8 Differen... Show Detail
- No：1589
- Displayed Date：2023/04/25 19:00
With communication using RS-485 of a general-purpose communication module (Type_ NP1L-RS□), is there any means to detect a line disconnection?

While 'DTR_ terminal ready' can be used with RS-232C, this control line is not present for RS-485. If no response is received while data are exchanged, re... Show Detail
- No：1322
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:20
Is it possible to use the optical converter NP1L-OL1 between processors as with the P-link?

The optical converter NP1L-OL1 is an optical converter of the SX bus. It cannot be used because the SX bus is not a link between processors. Show Detail
- No：1327
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:31
Can I replace NP1L-FL2 with NP1L-FL3 for FL-net communication?

When connected via 10BASE-T, you can replace it. There is no need to change the system definition. Before replacement, set the switches on the front of the N... Show Detail
- No：1524
- Displayed Date：2023/04/25 19:00
Is it possible to establish direct communication between Fuji Electric's PLCs and the original networks of Mitsubishi sequencers (MELSEC), NET/B, N...

The MICREX-SX does not include a communication module having interfaces with Mitsubishi's original networks, MELSEC-NET/B or NET/10 or CC-LINK. Alternativel... Show Detail
- No：1546
- Displayed Date：2023/04/25 19:00

11-20 of Total 53

Info & News

To Top of Page

Communication (Others)

Regional Websites

About Us

Products & Solutions

Investor Relations

Sustainability