A 'client' is a device that collects data. Since the PLC is a device from which data is collected, there is no OPC clien

The optical converter NP1L-OL1 is an optical converter of the SX bus. It cannot be used because the SX bus is not a lin

It occurs when any of the overrun, parity and framing errors is detected in the serial port of a general-purpose communi

The area is cleared when the power supply is turned off once and turned on again. The P/PE link memory is located in th

Common memory 1 and common memory 2 are handled together in terms of timing. However, to maintain the uniqueness of data

Set the port No. as described below. (1) For NP1L-RS2_ Set '0.' (2) For NP1L-RS4_ Set '1.' See the figure below for th

The number of M_OPEN FBs that can be opened simultaneously is limited to 56. The number of FBs that can be simultaneousl

※NP3L-FL3PXSの英文マニュアルなし。FAQの翻訳は実施したので、有効フラグOFFにして登録のみ実施。英文マニュアルを作った場合、公開する。（2021/1/22：光井、小笠原） NP3L-FL3PXS (PCI-Express-bu

Refreshing data in the link data area in FL-net takes place when data is received from another station. The local statio

It enables reception only when CD (Carrier Detection) is ON. (Other operations are the same as those in the DTE mode.)

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC > SPH > Communication (Others)

Latest FAQ

When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
I use DeviceNet interface module (NP1L-RD1) under DeviceNet master (NP1L-DN1). How can I specify NP1L-RD1 in the system definition?
In the communication module (NP1L-RS1/RS2/RS3/RS4/RS5), is it possible to change communication parameter such as fixed length to variable length af...
With the FL-net module (NP1L-FL1/FL2/FL3), is there any way to confirm that the data sent from the node-A have actually been received by the node-B?

GLOBAL

Search by category

Keyword Search

FAQ within [ Communication (Others) ]

1-10 of Total 53

≪ 1 / 6page ≫

There is an OPC server that supports the MICREX-SX (communication middleware, Type_ NP4N-MDLW). Is there an OPC client?

A 'client' is a device that collects data. Since the PLC is a device from which data is collected, there is no OPC client. Show Detail
- No：1553
- Displayed Date：2023/04/25 19:00
Is it possible to use the optical converter NP1L-OL1 between processors as with the P-link?

The optical converter NP1L-OL1 is an optical converter of the SX bus. It cannot be used because the SX bus is not a link between processors. Show Detail
- No：1327
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:31
With the general-purpose communication module (Type_ NP1L-RS□), in what cases does 'C0_ Hardware error detected during receiving' occur?

It occurs when any of the overrun, parity and framing errors is detected in the serial port of a general-purpose communication module. Show Detail
- No：1328
- Displayed Date：2023/04/25 19:00
In the P/PE link area, is the send area of the local station cleared when the power supply is turned off once and turned on again? Is there any set...

The area is cleared when the power supply is turned off once and turned on again. The P/PE link memory is located in the built-in memory (RAM) of the P/PE-l... Show Detail
- No：1436
- Displayed Date：2023/04/25 19:00
With the common memory of FL-net, I set word data with common memory 2 and bit data with common memory 1. Please describe the timing of transmissio...

Common memory 1 and common memory 2 are handled together in terms of timing. However, to maintain the uniqueness of data including those in common memory 1 a... Show Detail
- No：1311
- Displayed Date：2023/04/25 19:00
For the initial setting of a general-purpose communication module with only one communication port such as NP1L-RS2 and NP1L-RS4, is it correct to ...

Set the port No. as described below. (1) For NP1L-RS2_ Set '0.' (2) For NP1L-RS4_ Set '1.' See the figure below for the setting for each type of genera... Show Detail
- No：1383
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:45
Is there any limitation on the number of M_OPENs to be executed simultaneously? If there is a limitation, what is the maximum number?

The number of M_OPEN FBs that can be opened simultaneously is limited to 56. The number of FBs that can be simultaneously opened for each module depends on t... Show Detail
- No：1435
- Displayed Date：2023/04/25 19:00
Are there any FL-net boards compatible with Windows 10?

※NP3L-FL3PXSの英文マニュアルなし。FAQの翻訳は実施したので、有効フラグOFFにして登録のみ実施。英文マニュアルを作った場合、公開する。（2021/1/22：光井、小笠原） NP3L-FL3PXS (PCI-Express-bus-based FL-net board) is compatible ... Show Detail
- No：1464
- Displayed Date：2023/04/25 19:00
Which FL-net unit is responsible for refreshing data of the common memory with FL-net modules (Type_ NP1L-FL1/FL2/FL3)? Where is the master station?

Refreshing data in the link data area in FL-net takes place when data is received from another station. The local station data is refreshed by sending the la... Show Detail
- No：1424
- Displayed Date：2023/04/25 19:00
What will the operation be when the general-purpose communication parameter 8 of the non-procedure standard expansion FB for communication _Cfr* is...

It enables reception only when CD (Carrier Detection) is ON. (Other operations are the same as those in the DTE mode.) Show Detail
- No：1598
- Displayed Date：2023/04/25 19:00