The MICREX-SX series positioning module 'Type_NP1F-HD2A' replaces NC1F-VP1/FGU130B. Be aware of the following points:

Check the following system memory. (1) Configuration information %MW10.52 to %MW10.67 (WSM52 to 67) (2) Configuratio

The communication specification of the remote master does not control remote devices by the station No. Therefore, you c

When connected via 10BASE-T, you can replace it. There is no need to change the system definition. Before replacement, s

(1) With the SPH300/2000 Series, it is used to back up the data memory of the retained attributes, calendar IC memory, a

The MICREX-SX does not include a communication module having interfaces with Mitsubishi's original networks, MELSEC-NET/

Filter instructions are system FBs. System FBs that can be equalized are limited to_ The last value of the edge detectio

It counts the number of transmissions of message processing M_RECEIVE and M_SEND performed on the SX bus.

Check the following points_ (1) Check the input form specified on the application program. (2) Set Enable counting to

Use the 'Excitation timing output' signal for the Z-phase pulse when a stepping motor is used.

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC > SPH

Latest FAQ

When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
When I attempted to download a project to a CPU with user ROM card by using D300win, a message appeared saying 'Invalid loader command process!' an...

GLOBAL

Search by category

Keyword Search

FAQ within [ SPH ]

61-70 of Total 235

≪ 7 / 24page ≫

I use the MICREX-F series positioning module (Type_NC1F-VP1/FGU130B). What replaces it? Is there anything to be aware of when replacing it?

The MICREX-SX series positioning module 'Type_NP1F-HD2A' replaces NC1F-VP1/FGU130B. Be aware of the following points: 1) NP1F-HD2A is differential output t... Show Detail
- No：1463
- Displayed Date：2023/04/25 19:00
- Category： Function
I use the hot plug base board with station No. setup function (Type_NP1BS-13D). When I remove a module, how can I identify the removed module in D3...

Check the following system memory. (1) Configuration information %MW10.52 to %MW10.67 (WSM52 to 67) (2) Configuration fault information %MW10.68 to %MW1... Show Detail
- No：1482
- Displayed Date：2023/04/25 19:00
- Category： Main unit
When a remote terminal master (NP1L-RM1) has been registered in 1-to-N or N-to-N mode in the system definition, can I register a remote device as '...

The communication specification of the remote master does not control remote devices by the station No. Therefore, you cannot register remote devices as 'No ... Show Detail
- No：1486
- Displayed Date：2023/04/25 19:00
- Category： Support tool
Can I replace NP1L-FL2 with NP1L-FL3 for FL-net communication?

When connected via 10BASE-T, you can replace it. There is no need to change the system definition. Before replacement, set the switches on the front of the N... Show Detail
- No：1524
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
What is the data backup battery for the SPH Series used to back up? 　Are there any precautions in performing a battery-less operation?

(1) With the SPH300/2000 Series, it is used to back up the data memory of the retained attributes, calendar IC memory, and RAS information. (2) With the SPH2... Show Detail
- No：1534
- Displayed Date：2023/04/25 19:00
- Category： Main unit
Is it possible to establish direct communication between Fuji Electric's PLCs and the original networks of Mitsubishi sequencers (MELSEC), NET/B, N...

The MICREX-SX does not include a communication module having interfaces with Mitsubishi's original networks, MELSEC-NET/B or NET/10 or CC-LINK. Alternativel... Show Detail
- No：1546
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
I want to equalize filter instructions in a redundant system.

Filter instructions are system FBs. System FBs that can be equalized are limited to_ The last value of the edge detection FB, present counter value of the co... Show Detail
- No：1563
- Displayed Date：2023/04/25 19:00
- Category： Application
What does the sending/receiving counter for the structure variable RAS.RAS of the non-procedure standard expansion FB for communication _Cfr* count...

It counts the number of transmissions of message processing M_RECEIVE and M_SEND performed on the SX bus. Show Detail
- No：1569
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
Pulse counting is disabled on the high-speed input module (Type_ NP1X3206-A). What should I check?

Check the following points_ (1) Check the input form specified on the application program. (2) Set Enable counting to '1.' If the pulse count data regist... Show Detail
- No：1570
- Displayed Date：2023/04/25 19:00
- Category： Function
How can I provide Z-phase pulses when the equipment connected with the positioning control module (Type_ NP1F-MP2/MA2) uses a stepping motor?

Use the 'Excitation timing output' signal for the Z-phase pulse when a stepping motor is used. Show Detail
- No：1574
- Displayed Date：2023/04/25 19:00
- Category： Function

61-70 of Total 235

SPH

I/O
Error

Support tool

Info & News

To Top of Page

PKSHA FAQ logo

SPH

Regional Websites

About Us

Products & Solutions

Investor Relations

Sustainability