-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
- When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
- Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
- When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
- When I attempted to download a project to a CPU with user ROM card by using D300win, a message appeared saying 'Invalid loader command process!' an...
GLOBAL
Search by category
Keyword Search
FAQ within [ SPH ]
-
Is it possible to use a commercial CF card for the CPU module supporting CF card mounting?
Yes, it is possible. Use a card with the following memory capacities_ SPH300_ 2 GB or less SPH2000_ 32 GB or less (PIO mode supporting model) Note that so... Show Detail
- No：1593
- Displayed Date：2023/04/25 19:00
- Category： Accessory
-
Which mode does the Ethernet module (Type_ NP1L-ET1/ET2) support, half or full?
Only the NP1L-ET1 supports both modes automatically (auto negotiation). Since the NP1L-ET2 is designed for 10Base5 (coaxial), it is fixed to half duplex. Show Detail
- No：1554
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
-
Since the conversion accuracy after a scaling change remains within the specifications, rescaling is unnecessary. Show Detail
- No：1430
- Displayed Date：2023/04/25 19:00
- Category： I/O
-
This is because the SX bus loop-back plug is not connected. Connect a loop-back plug to the base board. Show Detail
- No：1335
- Displayed Date：2023/04/25 19:00
- Category： Error
-
The amounts of data transmitted or received are not limited as R_WRITE instruction/R_READ instruction but by the capacity of the memory from/to which data ar... Show Detail
- No：1324
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
-
No, you cannot use NW0H-CNV. The RS-232C/422 converter for personal computer loaders (Type_NW0H-CNV) needs to be supplied power from the PLC side, however, t... Show Detail
- No：1529
- Displayed Date：2023/04/25 19:00
- Category： Support tool
-
What measures can I take against external noise of the high-speed counter (Type_ NP1F-HC2)?
Use the recommended shielded twisted pair cable mentioned in the User's Manual. Also provide shielding. Show Detail
- No：1365
- Displayed Date：2023/04/25 19:00
- Category： Function
-
Possible causes include a fuse blowout in the high-speed output module (Type_ NP1Y32T09P1-A). Show Detail
- No：1342
- Displayed Date：2023/04/25 19:00
- Category： Function
-
It is not possible with D300win V2. The sampling trace function is supported by D300win V3.1.1.0. or later. [Related document] Refer to Section '11-7 Sampl... Show Detail
- No：1310
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
-
You cannot access general memory other than the memory for the multi-CPU from the other CPU. Access using the direct read/write FB is used for the access to ... Show Detail
- No：1645
- Displayed Date：2023/04/25 19:00
- Category： Main unit
31-40 of Total 235