-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
- When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
- Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
- When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
- When I attempted to download a project to a CPU with user ROM card by using D300win, a message appeared saying 'Invalid loader command process!' an...
GLOBAL
Search by category
Keyword Search
FAQ within [ SPH ]
-
Possible causes include a fuse blowout in the high-speed output module (Type_ NP1Y32T09P1-A). Show Detail
- No：1342
- Displayed Date：2023/04/25 19:00
- Category： Function
-
How can I write to the user ROM card of a standard CPU?
Turn off the write-protect switch of the user ROM card, mount it on the CPU module and transfer a program to write it to the user ROM card. Show Detail
- No：1344
- Displayed Date：2023/04/25 19:00
- Category： Main unit
-
There is a high-capacity battery for SPH300 (Type_ NP8P-BTS). Its battery capacity (approximately 2700 mA) is about 2.7 times that of the backup battery supp... Show Detail
- No：1360
- Displayed Date：2023/04/25 19:00
- Category： Accessory
-
The SX bus station number for the slot on which the CPU module is mounted is recognized as unused. Show Detail
- No：1382
- Displayed Date：2023/04/25 19:00
- Category： Main unit
-
No, it does not support the DPV1 function. It supports the DPV0 (I/O communication) function. Show Detail
- No：1391
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
For what application is the base board with station number setting switch used?
It is used as a base specified for 'system fail-soft start-up' operation, which is set when there is any base with some modules on which power is not turned ... Show Detail
- No：1411
- Displayed Date：2023/04/25 19:00
- Category： Main unit
-
It might be counting noise as a pulse. Take the following measures_ (1) Isolate the pulse generator and PLC from the noise source and shorten the wiring dist... Show Detail
- No：1427
- Displayed Date：2023/04/25 19:00
- Category： Function
-
The high-speed output module (Type_ NP1Y32T09P1-A)/high-speed input module (Type_ NP1X3206-A) cannot be mounted on the T-link expansion (RT1). Show Detail
- No：1433
- Displayed Date：2023/04/25 19:00
- Category： Function
-
The four-axis pulse string output terminal module (Type_ NR1SF-HP4DT) does not have a physical ±OT terminal. You can solve this problem by using software a... Show Detail
- No：1447
- Displayed Date：2023/04/25 19:00
- Category： Function
-
In the standard expansion counter FB _MHCNTH, CH0 operates but CH1 does not.
It seems that this problem was caused by an improper address setting for INDAT/OUTDAT assigned to the counter FB terminal. On a single module, assign the sa... Show Detail
- No：1539
- Displayed Date：2023/04/25 19:00
- Category： Function
11-20 of Total 235